Be Sure to visit the store to see whats new

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - teemu

Pages: [1] 2 3 ... 36
1
Forum Questions / Problems / Re: NOE store sign-in problems
« on: October 02, 2019, 12:43:00 AM »
This forum and webstore dosen't use https: therefore it is unsafe. Thats what i've been told for url's and thats why you get alert from browser or virusprotecting programs. Is it mandatory to use in forum..Probably not if here isn't any personal information etc. but webstores should use because there is addresses,names payment systems etc.

2
LAST CALL / Re: NOE-225-57 & NOE-228-57 (12)
« on: May 17, 2019, 10:33:43 PM »
Eerr... If not too late I would change my order... Just 2-cavity GC .225 diameter Aluminium. Thanks.

3
What you would like to see ran / Re: Sizing Die Bushings
« on: February 12, 2019, 12:27:27 AM »
Thanks!   Need to check if i missing some others "normal" sizing dies.. Taking all at one shipping then.

4
What you would like to see ran / Re: Sizing Die Bushings
« on: February 10, 2019, 08:55:51 AM »

5
LAST CALL / Re: NOE-225-57 & NOE-228-57 (10)
« on: January 26, 2019, 12:44:30 AM »
I like to get 3-cavity GC  Aluminium with Lyman style HP pin. .225 diameter. Thanks

6
What you would like to see ran / Re: Sizing Die Bushings
« on: December 19, 2018, 11:22:07 AM »
Yes and there was new list after that also... I'm quite sure...Well i could use some "wierd" body bushings since my old ideal mold .228 mold drops so much wider that when trying size down .228 body bushing bullet jammed in and needed use hammer and rod to get it off. So if this goes on i could take .229 .230 and .231...

7
What you would like to see ran / Re: Sizing Die Bushings
« on: December 19, 2018, 10:31:36 AM »
IRC on "old forum" was list of body and nose dies which was needed.... can't find that topic anymore...

9
Forum Questions / Problems / Re: need help signing in to wed store
« on: September 06, 2018, 10:21:48 AM »
Wierd....Just tested and works just fine. Same as always.

10
What you would like to see ran / Re: 225-51-SP-BA5 225450
« on: August 21, 2018, 10:31:11 PM »
Well that did't work...at this moment.  So pump it up..

11
Forum Questions / Problems / Re: $1'000 club
« on: August 21, 2018, 10:27:37 PM »
I wonder if you get a permanent 20% off after you spend your second $1000, and so on ;-)

Well....If so I could get molds pretty darn cheap then.. ;D But obvious it's not work that way.

12
What you would like to see ran / Re: 225-51-SP-BA5 225450
« on: August 07, 2018, 10:59:20 PM »
i could go try in some other forums...I need this mold  ;D

Edit: Put it on couple forum hope we get needed intrest.

13
What you would like to see ran / Re: 225-51-SP-BA5 225450
« on: August 03, 2018, 12:25:23 PM »
pump up!  8)

14
I noticed that those where gone about week ago but there was that section instead

15
There is Speciality Molds. Under that is BBt's and else.
http://noebulletmolds.com/NV/index.php?cPath=562

Pages: [1] 2 3 ... 36


Castpics and Reloader's Reference