Be Sure to visit the store to see whats new

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - 6pt-sika

Pages: [1] 2
1
Group Buy Discussions / Re: EAGAN MX4-30 ARD #2 w/ .299 - .301 Nose
« on: September 11, 2017, 08:58:29 AM »
Will this thing stabalize at 900-100 FPS in a 1:10 ?

I kinda want a 200-220 grain cast bullet for use in my 308 at subsonic .

2
(RD) Active Group Buys / Re: TLC432-360-RF (444 Marlin) (0)
« on: May 23, 2017, 07:19:27 AM »
"I WANT" an aluminum RG2 GC .

3
(RD) Group Buy Discussions / Re: TLC432-360-RF (444 Marlin)
« on: May 20, 2017, 10:31:08 PM »
I've already got one of these in a five GC as well as a single cavity HP before you did the RG molds . And with that being said I'd add an RG2 GC if you wanna cut it again .

4
🤔🤔🤔🤔🤔🤔

5
I as stated earlier have had one of the original Lee 432-240GC FN molds for several years . So I got an RG2 this time and used the supplied HP pins . Cast a bunch sized lubed and checked . Then loaded them for the 444 Marlin . Only tried H322 and used the charge I use for the FN version and a grain under . Sorry to say I only tried them at 50 yards so far but three at the same charge as the FN were in one nice round hole at 50 yards . Jay bird I run the pot hot , I just think after twenty years it's getting a little tired . So it may be time to upgrade to the Lyman 25 .

6
Got the mold this morning about 9AM had it cleaned with brake cleaner and sooted about twenty minutes later . Think I made about a dozen pours before I got it the way I wanted . Then cast perhaps 2 1/2 dozen . Might see if I can get them loaded up for my 444 !

7
Now if you please do the same thing with the Ranch Dog 432-300GC I'd like another RG2 aluminum .

8
Payment just sent via CC thanks 😉👍🏻

9
Hmmm it appears they went to the machine today ? When should the PM with the discount code be expected ?

10
Archived Buys / Re: Ranch Dog TLC432-240-RF (44 Mag & 444 Marlin) (13)
« on: April 21, 2017, 10:39:36 AM »
It will stay in last call until the morning the molds are being cut (produced).  Then, it will get moved to the closed group buys section.  I think this was towards the top of the list to be run (I can't remember for sure but I think it was up there in the top 3 molds to be run next).

I think what the guy meant by when will it come out of last call was more to when will it hit the machine .

11
Archived Buys / Re: Ranch Dog TLC432-240-RF (44 Mag & 444 Marlin) (11)
« on: March 21, 2017, 07:12:35 PM »
So what might the status be on this jewel ?

Should they be expected off by April 10 ?

12
Archived Buys / Re: Ranch Dog TLC432-240-RF (44 Mag & 444 Marlin) (11)
« on: March 06, 2017, 09:11:36 PM »
I'd be quite pleased if the same could be done with the RD 432-300GC .

13
Archived Buys / Re: Ranch Dog TLC432-240-RF (44 Mag & 444 Marlin) (5)
« on: February 16, 2017, 10:28:59 AM »
This bullet as a regular flat nose is a pretty decent killing bullet . I've had one of the original Lee Ranch Dog 6 cavity test molds ever since it's inception and as stated it killed very well pushed with a nice charge of H322 from a 24" barreled Marlin 444 .

So I'm curiouse to see how well it does with the big HP . I've had pretty decent luck with the Lyman 429244 HP in the past . Not as good of luck with the Lyman 429640 Devestater HP . Also had pretty decent luck with the NOE/RD 432-265GC HP . And my own version of the RD bullet in the BRP/RD 432-375CG HP and 432-400GC HP . I used the NOE/RD 432-350GC HP as well and it performed adequately . My only other HP mold is one of the Mihec 433-295GC HP and it literally knocked the fire out of the only deer I ever fired it at !

14
(RD) Group Buy Discussions / Re: TLC432-300-RF (44 Mag & 444 Marlin)
« on: February 11, 2017, 09:35:04 PM »
I've been wanting this in an HP GC version ever since you started your mold business .

So yes I'd like one of these in an RG2 GC aluminum .

15
Archived Buys / Re: Ranch Dog TLC432-240-RF (44 Mag & 444 Marlin)
« on: February 09, 2017, 06:11:01 PM »
"I WANT" an aluminum RG2 GC and Lyman TP please .

Pages: [1] 2


Castpics and Reloader's Reference