259-102-FN (259418)

Home › Forums › NOE Forums › NOE Archive › Historical Archive › Group Buys › Group Buy Discussions › 259-102-FN (259418)

  • This topic is empty.
  • Creator
    Topic
  • #488217
    SwedeNelson
    Keymaster
      Up
      0
      Down
      ::

      Had a request to see if we can get some interest in this one


      Bullet maker, maker
      Al Nelson

    Viewing 15 replies - 1 through 15 (of 15 total)
    • Author
      Replies
    • #499591
      teemu
      Participant
        Up
        0
        Down
        ::

        I’m in

        #499592
        michaelmassar
          Up
          0
          Down
          ::

          Any chance the driving band could thinner and not so wide by chance this is for Airguns request

          #499593
          teemu
          Participant
            Up
            0
            Down
            ::

            This is workin well at orginal look in airguns. Tofazfou is shooting well this same bullet expept it is HP.  Correct me if im wrong You now were Tofazfou is…

            Edit: This is orginal bullet from Ideal mold..
            13931769.t.jpg

            Edit: Ok I was wrong…

            But still interested that Al’s drawing…So i’m in…But I also don’t mind if drawing is changed some direction…Still in on this one

            #499594
            teemu
            Participant
              Up
              0
              Down
              ::

              My original idea was to save that historical mold and get “modern” version that historical mold. But I’m ready for changes if that makes that more suitable to most buyers. And if it is ok for Al

              This is Spitzer version My friend just modified that orginal drawing
              13933630.t.jpg

              #499595
              teemu
              Participant
                Up
                0
                Down
                ::

                Other possibilty maybe?
                13935467.t.jpg

                Click larger image…

                anyway i’m interested both versions

                #499596
                teemu
                Participant
                  Up
                  0
                  Down
                  ::

                  Not even Spitzer get anybody interested ?  :-

                  #499597
                  frankelliott
                  Participant
                    Up
                    0
                    Down
                    ::

                    This is a modernized 418 that I did, quite a while back:

                    http://noebulletmolds.com/smf/index.php/topic,224.0.html

                    Frank

                    #499598
                    teemu
                    Participant
                      Up
                      0
                      Down
                      ::

                      Almost but base is different. That Spitzer which my friend was drawing has 5.4 degree angle. And only 2 grease groove.
                      That is copy of old Ideal mold.

                      Hoping it or Al’s drawing gets attention but not quite what needs to get those molds in GB  :'(

                      #499599
                      teemu
                      Participant
                        Up
                        0
                        Down
                        ::

                        Is there any body out there?  :-

                        #499600
                        teemu
                        Participant
                          Up
                          0
                          Down
                          ::

                          Bump

                          NOE is only company that I now who makes Spitzers….This is proven to be good bullet atleast in Airguns… :'(

                          #499601
                          teemu
                          Participant
                            Up
                            0
                            Down
                            ::

                            Is it possible to move this thread to Air gun section? could get better attention… :-

                            #499602
                            rsterne
                            Participant
                              Up
                              0
                              Down
                              ::

                              I would be interested in the original version with the 1/8″ Meplat, if the driving bands were narrowed up, leaving a wide space between them, to reduce bore contact for airgun use….

                              Bob

                              #499603
                              teemu
                              Participant
                                Up
                                0
                                Down
                                ::

                                Well I could take that one also… Looks like I don’t get that Spitzer model even that was proved to work well, atleast I recall reading some place that Tofazfou use that bullet…

                                #499604
                                rsterne
                                Participant
                                  Up
                                  0
                                  Down
                                  ::

                                  If it was a HP, how could it be a Spitzer?…. I could see doing a HP with a 1/8″ Meplat (as per the original drawing) but not if you go smaller, on a cast bullet…. As I understand it, the RG molds require at least a 0.200″ Meplat, so the only way NOE can do a HP on that bullet would be using a Lyman style removable pin with handle, and then only one cavity per block…. I’m not sure what is the smallest Meplat they can do that on…. Al?….

                                  Bob

                                  #499605
                                  teemu
                                  Participant
                                    Up
                                    0
                                    Down
                                    ::

                                    That cad drawing was made from Ideal mold which is HP and it is Lyman style pin and 1-cavity mold. That Spitzer is just same as first drawing but altered to Spitzer. Ideal has also Spitzer mold,I think  RJ porter has it but I can’t remember which number that is…But weight is same than that ideal which I have. Approximately 96 or 98 grains.

                                    First idea was to make exact copy of that ideal with or without hp because that mold is so old I think they stop making it around 1952 or so on. Mold still cast nice bullets and no issues with that but my opinion it should retreat to earned retirement days on my prize shelf.

                                    It is almost impossible to find some where that orginal Ideal Spitzer mold so this is only place which I know to get Spitzer molds. I’ve been looking over year or two but I haven’t got any luck, then I found that my Ideal mold and bought it immediately.Those are pretty rare in small calibers. I know place where are quite many Ideal molds but those are calibers which I don’t need

                                  Viewing 15 replies - 1 through 15 (of 15 total)
                                  • You must be logged in to reply to this topic.