TLC359-175 RF | NOE Bullet Moulds

This topic is empty.

Creator

Topic
2015-10-25 at 21:19 #488392
stevenhart
Participant
Up
0
Down
::
Hello guys.

I would love to this this mold available again. I want to get it for my Marlin 1894CS. Personally I would take a two cavity, gas check mold in aluminum.

Thanks again,

Steve in N CA
Creator

Topic

Viewing 15 replies - 1 through 15 (of 15 total)

Author

Replies
2015-10-29 at 13:36 #501197
Ranch Dog
Up
0
Down
::
Great, thanks for bring your interest here.
2015-10-29 at 14:13 #501198
robertbarker
Up
0
Down
::
I’m in for this one and the 190gr both in plain base solid.
2015-10-29 at 15:56 #501199
johnlarke
Up
0
Down
::
Yes, I would be interested in purchasing an aluminum mold gas check 2 or 4 cavity .
2015-10-29 at 23:17 #501200
stevenhart
Participant
Up
0
Down
::
Excellent.

There is one more guy over on Cast Boolits also. I will try to get more interested.

Steve in N CA
2015-10-29 at 23:27 #501201
stevenhart
Participant
Up
0
Down
::
I started a thread in the group buy discussions. Could you guys go over there and post you interest please?

Thanks a lot.
2015-11-02 at 19:48 #501202
stevenhart
Participant
Up
0
Down
::
I think we can call this off and try again next summer.

Thank you gentlemen.
2015-11-06 at 01:46 #501203
johnmortimer
Participant
Up
0
Down
::
This belongs in the RD sub-forum. I’m in for sure.
2015-12-30 at 22:26 #501204
zanesullins
Spectator
Up
0
Down
::
This should be great for 38 and 357 leverguns. I’d like a Rg2 GC or a Rg4 2gc 2PB if it was ran. With Hp, cup and flat pins.
2016-03-07 at 03:50 #501205
erikdorothy
Participant
Up
0
Down
::
And here I was about to start a relaunch thread. . .

I’m IN!

4C brass for sure. Solid, HP, or even both yet to be determined. . . Head scratchin’ to be done.
2016-03-27 at 23:56 #501206
johnmortimer
Participant
Up
0
Down
::
I’m in.
2016-04-01 at 00:31 #501207
erikdorothy
Participant
Up
0
Down
::
Might one of our more tech-saavy players be able to link in a pic of this bullet from the Ranch Dog Molds section of the NOE site main menu? Might move faster if we had some eye candy. I can attend to that over at Boolits, but the process here eludes me. . .
2016-04-02 at 23:30 #501208
Irascible
Participant
Up
0
Down
::
How about a drawing of this
2016-04-03 at 00:48 #501209
erikdorothy
Participant
Up
0
Down
::
How about a drawing of this

http://noebulletmolds.com/NV/product_info.php?cPath=71_78&products_id=456&osCsid=oodns2j5aqhc9tqsuj0kukngq6

It’s in the .358 link of the “Ranch Dog Molds” menu. Can’t figure out how to post it up here.
2016-04-04 at 02:15 #501210
davidlawrence
Participant
Up
0
Down
::
I want this mold too. Missed out the first time and would like to shoot this one in my 357 Maximum.
2016-04-12 at 03:36 #501211
daveeddy
Up
0
Down
::
for what its worth, I wouldn’t mind getting a spare mold for this bullet,
count me in if it helps get a run started,
Author

Replies

Viewing 15 replies - 1 through 15 (of 15 total)

You must be logged in to reply to this topic.