22 TCM Bullet 225-35-RF | NOE Bullet Moulds

This topic is empty.

Creator

Topic
2017-10-18 at 19:54 #489482
Full.Lead.Taco
Keymaster
Up
1
Down
::
22 TCM Bullet 225-35-RF

Any 22 TCM shooters out there who would be interested in this mold design? Could also work as a light weight plinker bullet for .22 cal rifles.
Creator

Topic

Viewing 15 replies - 1 through 15 (of 15 total)

Author

Replies
2017-10-18 at 21:59 #509472
rsterne
Participant
Up
0
Down
::
I would be interested in a 2-cavity with a Lyman style HP pin in one cavity…. I would also be interested in the same bullet in a slightly smaller diameter for airguns….

Bob
2017-10-19 at 05:53 #509473
teemu
Participant
Up
0
Down
::
I’m interested also…I can size it down for airguns.
2017-10-23 at 19:59 #509474
tylercrowe
Participant
Up
0
Down
::
I’d be interested in an HTC version of this, for sure.
2017-10-25 at 03:49 #509475
teemu
Participant
Up
0
Down
::
Hope there will be 2 separated GB then…Airgunners and plinkers don’t need HTC molds.
2017-10-25 at 20:28 #509476
tylercrowe
Participant
Up
0
Down
::
Hope there will be 2 separated GB then…Airgunners and plinkers don’t need HTC molds.

Teemu, is there any downside to using an HTC mold in an airgun? The main advantage I see to HTC molds is just how easy they are to cast.
2017-10-26 at 03:18 #509477
teemu
Participant
Up
0
Down
::
Well on downside is it is like lead clump. There is so much less force behind that bullet that should have atleast one driving band to ease friction on barrel. Or bullet should be very small caliber like this one but I haven’t got any HTC mold but I suspect it wont work like “normal” bullet with grooves and driving bands. Altought not all HTC models are like clump. But hey You never know if You don’t test any so it depends on drawing….

I have one mold which is quite like HTC model and yes you are right it is easy to cast….
2017-10-26 at 17:51 #509478
gregthompson
Participant
Up
0
Down
::
Yes I would go for a 22 TCM bullet for HTC
2017-10-27 at 07:15 #509479
teemu
Participant
Up
0
Down
::
Most part seems to be going in to HTC models here and other places….I know it is better for You guys who shooting other propellant than air. Sadly it is dropping us airgunners off board. Well it is quanity what counts not couple others who looking “normal bullet” desings. Altought this one hasn’t got much attention either way…
2017-10-27 at 17:02 #509480
teemu
Participant
Up
0
Down
::
Hmm doing some research and there is swagged bullet for airguns those like HTC models and those work in some airguns quite well. Maybe I should get one HTC mold and give a try
2017-10-27 at 17:20 #509481
Full.Lead.Taco
Keymaster
Up
0
Down
::
Hmm doing some research and there is swagged bullet for airguns those like HTC models and those work in some airguns quite well. Maybe I should get one HTC mold and give a try

It would be interesting to see the results.
2017-10-27 at 17:26 #509482
teemu
Participant
Up
0
Down
::
Yeah interested to see too. Altougt those swagged bullets was for.45 cal Airgun…But I don’t think there is matter which caliber is it.
2017-10-27 at 20:31 #509483
tylercrowe
Participant
Up
0
Down
::
Teemu,

I have NOE HTC molds in 9mm, 45, and 44. I know those are big for most airguns but would be happy to send a few your way to test the HTC design in airguns if you have one in one of those three calibers.
2017-10-28 at 03:33 #509484
teemu
Participant
Up
0
Down
::
I have 2 x .45 ….and so on but winter is coming snow rains down here yesterday so my tests are gone until May comes…And I was checking .225 HTC mold from NOE. Because I have one .224 match grade barreled project coming..

tzzler44 basic airgun calibers…It was long ago when was only Haenels… Those aren’t big for airguns… Friend owns 20mm airgun. And that is power house 4215 J about 3100 footpound. In airgun section is some tests and videos from that monster under topic: some pcp airguns. From start to nowdays. All action starts link page 7… And those bullet speeds and so on are measured on Labradar..

Teaser…

darn…There is one good looking .45 HTC mold also…poor wallet :
2017-10-29 at 20:29 #509485
Full.Lead.Taco
Keymaster
Up
0
Down
::
I talked to Al about combining both bullets into one group buy. He said it would be ok. That way everyone wins! Group buy will be posted shortly.
2017-10-29 at 21:04 #509486
Full.Lead.Taco
Keymaster
Up
0
Down
::
group buy is now active for both the HTC and regular molds:

http://noebulletmolds.com/smf/index.php/topic,2298.0.html
Author

Replies

Viewing 15 replies - 1 through 15 (of 15 total)

You must be logged in to reply to this topic.