Sizing Die Bushings

Home › Forums › NOE Forums › NOE Archive › Historical Archive › Inventory Runs › What you would like to see ran › Sizing Die Bushings

  • This topic is empty.
  • Creator
    Topic
  • 2018-12-19 at 16:46 #489820
    rsterne
    Participant
      Up
      -13
      Down
      ::

      How about adding any body or nose (please specify) sizing die bushings you need, either out of stock or new ones you need, to this thread?….

      I need a 0.171″ and a 0.170″ body bushing…. I also need a 0.283″ and a 0.282″….

      Bob

    • Creator
      Topic
    Viewing 10 replies - 1 through 10 (of 10 total)
    • Author
      Replies
    • 2018-12-19 at 17:31 #511384
      teemu
      Participant
        Up
        0
        Down
        ::

        IRC on “old forum” was list of body and nose dies which was needed…. can’t find that topic anymore…

        2018-12-19 at 17:37 #511385
        rsterne
        Participant
          Up
          0
          Down
          ::

          I couldn’t find it either, despite a search…. NOE did a large run of bushings after that thread, and filled out a lot of the missing inventory, plus added the airgun bushings…. That is why I decided to start a new thread….

          I don’t need any, but I know there is talk of making bullets for .177 airguns, which could require bushings from 0.174 to 0.179…. I need ones just under bore size for the .172 cal NOE bullets….

          Bob

          2018-12-19 at 18:22 #511386
          teemu
          Participant
            Up
            0
            Down
            ::

            Yes and there was new list after that also… I’m quite sure…Well i could use some “wierd” body bushings since my old ideal mold .228 mold drops so much wider that when trying size down .228 body bushing bullet jammed in and needed use hammer and rod to get it off. So if this goes on i could take .229 .230 and .231…

            2019-01-31 at 16:36 #511387
            rsterne
            Participant
              Up
              0
              Down
              ::

              I just talked to Al, and he plans to run these additional bushings soon and put them in the Store…. If you have any additional requirements, post them NOW….

              Bob

              2019-02-09 at 02:14 #511388
              jamesseiler
              Participant
                Up
                0
                Down
                ::

                I just opened up a .173 3 cavity mold and also sizer. I do have a .172 sizer and I think .171, that I will probably not need now.

                Others have mentioned a smaller body die for .217 seems some guns are tighter bore .215 , on my AT Nova Liberty.

                2019-02-10 at 15:55 #511389
                teemu
                Participant
                  Up
                  0
                  Down
                  ::

                  http://noebulletmolds.com/NV/product_info.php?cPath=564_104_411&products_id=3703

                  There is .215 body sizing die at store

                  2019-02-12 at 00:24 #511390
                  SwedeNelson
                  Keymaster
                    Up
                    0
                    Down
                    ::

                    teemu

                    229 .230 and .231… will see what we can do!
                    Thanks

                    Bullet maker, maker
                    Al Nelson

                    2019-02-12 at 07:27 #511391
                    teemu
                    Participant
                      Up
                      0
                      Down
                      ::

                      Thanks!  Need to check if i missing some others “normal” sizing dies.. Taking all at one shipping then.

                      2019-03-26 at 04:45 #511392
                      danlaney
                      Participant
                        Up
                        0
                        Down
                        ::

                        New guy here.

                        Was browsing the website and notice that the sizing die is out of stock and don’t see a .310 body die listed either.

                        2019-04-10 at 20:54 #511393
                        stevephillips1
                        Participant
                          Up
                          0
                          Down
                          ::

                          I could really use a .430 Body Bushing!

                        • Author
                          Replies
                        Viewing 10 replies - 1 through 10 (of 10 total)
                        • You must be logged in to reply to this topic.