.25 cal BBT Airgun HPs

Home › Forums › NOE Forums › NOE Archive › Historical Archive › Inventory Runs › What you would like to see ran › .25 cal BBT Airgun HPs

  • This topic is empty.
  • Creator
    Topic
  • 2019-10-14 at 22:31 #490003
    rsterne
    Participant
      Up
      -8
      Down
      ::

      The .25 cal airgun Bob’s Boattails have been out of stock for a long time…. Al made some of the .22 cal 30 gr. Airgun BBTs as a HP using the new thin RG pins, and they are a screaming success…. Please put your name down here if you would like to see the 41 gr. and 50 gr. BBTs in .25 cal made as RG2 and RG4 moulds to produce both FN ad HP bullets from the same mould….

      n.o.e._bullet_moulds_250-41-hp_bt_bk2__sketch.jpg

      There are a couple of moulds left in the store for the 60 gr…. but that should be made in the RG moulds as well….

      The same tooling can be used to produce that bullet as a .257 cal….

      n.o.e._bullet_moulds_257-64-hp_bt_bp5__sketch.jpg

      Specify if you want the .25 cal in 41 gr., 50 gr. or 60 gr. or the 64 gr. in .257 cal… I would like all of them as HPs, in the new RG4 moulds….

      Bob

    • Creator
      Topic
    Viewing 9 replies - 1 through 9 (of 9 total)
    • Author
      Replies
    • 2019-10-15 at 00:03 #511979
      Mrgray2710
        Up
        0
        Down
        ::

        OMG for real dude! How can we buy your  stuff if it’s not in stock??? Looking for the .250 Hunter and magnum molds as well as the 41 gr and 50 gr bbt slugs in .250. sure would be nice if they were in stock. Pissin on the wheels of progress over here ya know.

        2019-10-15 at 02:13 #511980
        glensuzuki
        Participant
          Up
          0
          Down
          ::

          I’m in for both the 41 and 51 grain with RG pins. I’ve been waiting patiently for a long time too.

          2019-10-15 at 20:59 #511981
          matthewtroiano
          Participant
            Up
            0
            Down
            ::

            Count me in for a 250-41

            2019-10-19 at 22:30 #511982
            mohunter
              Up
              0
              Down
              ::

              the .250  magnum mold as well as the 41 gr and 60 gr bbt slugs in .250. i have been checking back with you for a year or so waiting for them to be in stock . it is hard to buy them when there aren’t  any. Also rg2 is fine but would be ok with rg4. And thanks for getting this going.

              2019-10-25 at 16:51 #511983
              lorenmock
              Participant
                Up
                0
                Down
                ::

                I would buy one of the 250-41 HP molds

                2019-11-18 at 17:58 #511984
                naiffattah
                Participant
                  Up
                  0
                  Down
                  ::

                  I would buy one of the 250-41 HP molds

                  2019-12-17 at 22:35 #511985
                  alaindegrasse
                  Participant
                    Up
                    0
                    Down
                    ::

                    I would buy one of the 250-41 HP molds as well

                    2020-01-10 at 14:01 #511986
                    ors
                      Up
                      0
                      Down
                      ::

                      I would buy 250-41-hp, 250-50-hp,250-50-fn and 253-51-fn 5 cavity bt w/hp. And few airgun body sizing sets from .250 to .254.

                      2020-02-24 at 23:13 #511987
                      rsterne
                      Participant
                        Up
                        0
                        Down
                        ::

                        Lots of interest here, for sure…. I will keep bugging Al….  ;)

                        Bob

                      • Author
                        Replies
                      Viewing 9 replies - 1 through 9 (of 9 total)
                      • You must be logged in to reply to this topic.