RCBS-Hodgdon in .578

Home › Forums › NOE Forums › NOE Archive › Historical Archive › Group Buys › Group Buy Discussions › RCBS-Hodgdon in .578

  • This topic is empty.
Viewing 15 replies - 1 through 15 (of 32 total)
  • Author
    Replies
  • #499217
    adamsutherland
    Moderator
      Up
      0
      Down
      ::

      If you send half a dozen as cast bullets to Al he would do a drawing.

      I’d be up for one, but dropping 0.576″ from pure lead would suit me better, why over bore diameter? It is a Minie after all.

      #499218
      maillemaker
        Up
        0
        Down
        ::

        I’d be glad to send some bullets, just let me know where to send them.

        I cast mine at .578 in pure lead and then size/lube to .576 in my Lyman Lubrisizer.

        Steve

        #499219
        adamsutherland
        Moderator
          Up
          0
          Down
          ::

          Send them as cast to Al at NOE.

          I’d sooner have them drop at 0.576″ from an NOE mould.

          #499220
          patkelly
            Up
            0
            Down
            ::

              Yeah……put me down for a .578  I have to size for .578  .576 & .575 for seven different muskets so the .578 works best. Anything smaller then that and I’d not be interested.
            Thanks
              Pat

            #499221
            adamsutherland
            Moderator
              Up
              0
              Down
              ::

              I cast mine at .578 in pure lead and then size/lube to .576 in my Lyman Lubrisizer.

              Steve

              Where do you get the H&I dies for the Lyman lubsizer in 0.576″?

              The walls must be pretty thin especially where the “O” ring groove is.

              #499222
              adamsutherland
              Moderator
                Up
                0
                Down
                ::

                BTW I’m not interested in a 0.578″ mould as I have no requirement for and oversize mould, so count me out.

                #499223
                maillemaker
                  Up
                  0
                  Down
                  ::

                  Where do you get the H&I dies for the Lyman lubsizer in 0.576″?

                  The walls must be pretty thin especially where the “O” ring groove is.

                  I buy my sizing dies for the Lyman Lulbrisizer from S&S firearms.  I have dies for .575 up to .579. 

                  http://www.ssfirearms.com/proddetail.asp?prod=SA450

                  Like RaiderANV, I have arms that prefer .578 and .576, so a .578 would offer me maximum flexibility.  I’d be running them through my sizer to lube them regardless of size.

                  Steve

                  #499224
                  adamsutherland
                  Moderator
                    Up
                    0
                    Down
                    ::

                    Could you measure the wall thickness of the 0.578″ at the “O”ring groove for please or just the die’s outside diameter in the “O” ring groove, just curious.

                    #499225
                    maillemaker
                      Up
                      0
                      Down
                      ::

                      Yeah I’ve been meaning to mail them.  I need to get a small flat rate box from the PO.

                      As cast using pure lead, the OD of the bullet is measuring .579.-580.

                      The inner diameter of the main grease groove is .498.

                      I don’t have a good way to measure the wall thickness as the hollow cavity is conical.

                      However, the apex of the truncated cone is .132 in diameter, and the base of the cone is about .432, and it is .358 tall.

                      I made a 3D Cad model of this bullet in Solid Edge.  I can make a drawing for you.

                      Steve

                      #499226
                      adamsutherland
                      Moderator
                        Up
                        0
                        Down
                        ::

                        You need to speak with Al about the bullet drawings.

                        I’m interested in your 0.578″ H&I die and am asking would you measure the outside diameter of the die and outside diameter of the die in the groove that the “o”ring sits in please?

                        #499227
                        maillemaker
                          Up
                          0
                          Down
                          ::

                          I’m afraid I don’t follow your terminology.  I don’t know what an H&I die is.

                          Hopefully this drawing will tell you what you want to know:

                          d8lG4zC.png

                          Steve

                          #499228
                          adamsutherland
                          Moderator
                            Up
                            0
                            Down
                            ::

                            The H&I die is Lyman’s name for the sizing die that you put in your  Lyman Lubrisizer for sizing bullets down to 0.576″ as your post above.

                            I am interested in the dimensions of the sizing die and would just like to know the outside diameter of you sizing die across the groove at the top where the “o” ring goes without the “o” ring in place.

                            I’d also be interested in the outside diameter of the die across the lube holes.

                            #499229
                            maillemaker
                              Up
                              0
                              Down
                              ::

                              Ooooooohhhh!!  I get it now!

                              You want to know about the sizing die!!!

                              Yeah I can measure that when I get home.

                              Steve

                              #499230
                              adamsutherland
                              Moderator
                                Up
                                0
                                Down
                                ::

                                That is right, the H&I die.

                                #499231
                                maillemaker
                                  Up
                                  0
                                  Down
                                  ::

                                  The sizing die outer diameter is .700″.  The diameter at the bottom of the groove is .652″.  With a bore size of .576″ this results in a minimum wall thickness of .038″

                                  Steve

                                Viewing 15 replies - 1 through 15 (of 32 total)
                                • You must be logged in to reply to this topic.