"Real" Keith bullet moulds

Home › Forums › NOE Forums › NOE Archive › Historical Archive › Group Buys › Group Buy Discussions › "Real" Keith bullet moulds

  • This topic is empty.
  • Creator
    Topic
  • 2015-12-21 at 15:28 #488501
    k7sparky
    Participant
      Up
      0
      Down
      ::

      Is there enough intereast in Keith SWC moulds that Keith had the say on final design to get group buys together?

      I’m in for RG4s and RCBS nose punches in 38,44 & 45 cal

      This discussion start is in response to an older thread  started August 05  “Real” Keith Bullets started by LAH  on CB that has grown from 81/2 pages to 13 since October and is worth reading for history.

      There are 38, 41, 44 & 45 samples cast from original available that Prochko (PJP) worked with Keith to get it right read page 8
      http://castboolits.gunloads.com/showthread.php?1954-quot-Real-quot-Keith-Bullets

      So how about some REAL Keith moulds?

    • Creator
      Topic
    Viewing 15 replies - 1 through 15 (of 34 total)
    1 2 3
    • Author
      Replies
    • 2015-12-21 at 15:44 #501811
      stevendragonjr
      Participant
        Up
        0
        Down
        ::

        Ones in 38 and 45 for me.  Just want solid versions.

        2015-12-21 at 17:46 #501812
        bennyritter
          Up
          0
          Down
          ::

          I would also be in for the 38 and 45,solid and hollowpoint

          2015-12-21 at 18:42 #501813
          5shot
            Up
            0
            Down
            ::

            One in 45 for me.

            2015-12-21 at 19:01 #501814
            k7sparky
            Participant
              Up
              0
              Down
              ::

              I didn’t plan on limiting this to 4 Calibers of the “original 4 steel masters”  that may have been tossed.

              I picked 4 originally mentioned and I had seen vetted on the LAH thread.

              If you want another cal get it vetted on the CB thread,  MAKE SURE samples are available and add “I’m in for ?”

              If a cal gets close and needs one or 2 more and I don’t notice it, PM me and I will probably jump in just for a piece of history.

              2015-12-21 at 20:32 #501815
              brianadams
              Participant
                Up
                0
                Down
                ::

                I’d suggest restarting and breaking this up into a separate thread for each caliber: “Real Keith .45”, “Real Keith .38” etc. It will make counting the “I wants” a lot easier.

                2015-12-21 at 21:38 #501816
                k7sparky
                Participant
                  Up
                  0
                  Down
                  ::

                  I’d suggest restarting and breaking this up into a separate thread for each caliber: “Real Keith .45”, “Real Keith .38” etc. It will make counting the “I wants” a lot easier.

                  Checked with a moderator before starting this thread and the suggestion was do it this way instead of separate threads.

                  Since he is the keeper of the score card I let him pick his poison

                  2015-12-21 at 23:53 #501817
                  Anonymous
                    Up
                    0
                    Down
                    ::

                    I’ve got to stop looking at the forum topics it’s expensive! First I’d like to see drawings secondly I’d be in for pairs of moulds a 5 cavity and an RG4 along with top punches in the following order 41, 44, 45 then 38. If my math is right that’s eight moulds … gotta start saving now.

                    2015-12-22 at 00:25 #501818
                    k7sparky
                    Participant
                      Up
                      0
                      Down
                      ::

                      I’d like to see drawings

                      Scuttlebutt over on CB is the drawings are in the works.  Enough interest will get us drawings.

                      Till it looks like we have the interest I would rather see Al getting moulds out the back door than doing drawings that may be for not.

                      2015-12-22 at 17:49 #501819
                      jasonchrist
                      Participant
                        Up
                        0
                        Down
                        ::

                        I would be on board for .360″ and .434″ solid molds, pending review of the drawings.

                        2015-12-22 at 22:54 #501820
                        micaelnetz
                        Participant
                          Up
                          0
                          Down
                          ::

                          I would be interested in a .358 if it could be made with a Hollow Base (RG).

                          2015-12-23 at 03:26 #501821
                          stephenbennett
                            Up
                            0
                            Down
                            ::

                            I’d take a two cavity .357, 41, .44 and .45 Keith molds all PBed
                            thanks, Steve

                            2015-12-23 at 17:51 #501822
                            michaelwillett
                            Participant
                              Up
                              0
                              Down
                              ::

                              I’ve seen the example cast boolits from the original thread and Swede hasn’t done us wrong yet so I’m in like Flynn!  I want an RG4 of ALL calibers 38, 41, 44 and 45 plus Lyman top punches for said moulds.

                              I would be very, very shocked if this doesn’t happen unless the drawings are significantly different from the samples but I have full faith in Swede to get them correct.

                              2015-12-23 at 20:42 #501823
                              SwedeNelson
                              Keymaster
                                Up
                                0
                                Down
                                ::

                                OK – this is what I have received from Beagle333 and Paul in Idaho
                                Talked with Paul and got some interesting history on the samples.





                                2015-12-23 at 22:00 #501824
                                charlesgilbert
                                Participant
                                  Up
                                  0
                                  Down
                                  ::

                                  Beautiful ;D ;D! Are you going to break them up into individual buys/sales or how is it going to work?  8)

                                  2015-12-23 at 22:30 #501825
                                  michaelwillett
                                  Participant
                                    Up
                                    0
                                    Down
                                    ::

                                    Beautiful ;D ;D! Are you going to break them up into individual buys/sales or how is it going to work?  8)

                                    What he said.  I’m all in.

                                  • Author
                                    Replies
                                  Viewing 15 replies - 1 through 15 (of 34 total)
                                  1 2 3
                                  • You must be logged in to reply to this topic.