223-38-RN Hill (For .22 LR Reloading) (10)

Home › Forums › NOE Forums › NOE Archive › Historical Archive › Group Buys › Archived Buys › 223-38-RN Hill (For .22 LR Reloading) (10)

  • This topic is empty.
  • Creator
    Topic
  • 2018-05-01 at 13:04 #489662
    Full.Lead.Taco
    Keymaster
      Up
      0
      Down
      ::

      223-38-RN Hill (For .22 LR Reloading)

      We will be running 2 cavity, 2 cavity Brass, 3 cavity, 3 cavity Brass, 4 cavity, 5 cavity and 5 cavity Brass.
      Will assume mould blocks will be Aluminium if not requested as Brass.

      Top punch, wrenches and sprue lube are extras now if you want them

      Prices will be our standard website prices ( http://www.noebulletmoulds.com )
      2 cavity $79.00
      2 cavity Brass $101.00
      3 cavity $86.00
      3 cavity Brass $108.00
      4 cavity $92.00
      5 cavity $99.00
      5 cavity Brass $121.00

      Lyman/RCBS style Top Punch $5.00
      Saeco style Top Punch $7.50
      Mould Wrenches / Sprue Lube $2.50
      Lyman Single pin HP with Handle ADD $35.00 (1 cavity only)

      Will run this as soon as we get 10 signed up and we get the tooling in.
      Will have them listed on our website as a inventory item as soon as we have them ran
      So you can use Pay-Pal, Credit Card or Check / Money order
      Post a “I want” and receive a 15% discount off the website
      We will PM a discount code for you to use at check out

      If you have question – Visit our website or PM me

      Thanks
      Swede Nelson

    • Creator
      Topic
    Viewing 15 replies - 16 through 30 (of 44 total)
    1 2 3
    • Author
      Replies
    • 2018-05-19 at 05:33 #510660
      adamsutherland
      Moderator
        Up
        0
        Down
        ::

        List updated.

        2018-05-24 at 12:27 #510661
        teemu
        Participant
          Up
          0
          Down
          ::

          Can I change my order…. 3-cavity aluminium with  Lyman style HP pin and Lyman/RCBS style Top Punch. Thanks.

          2018-05-24 at 13:33 #510662
          adamsutherland
          Moderator
            Up
            0
            Down
            ::

            Updated.

            2018-05-24 at 15:20 #510663
            tomkerrigan
            Participant
              Up
              0
              Down
              ::

              I just saved some money, it’s about .060″ too long to fit my Huben.  Regards, Tom

              2018-05-24 at 15:53 #510664
              adamsutherland
              Moderator
                Up
                0
                Down
                ::

                I just saved some money, it’s about .060″ too long to fit my Huben.  Regards, Tom

                HP’ing might get you there.  ;) :D

                2018-05-24 at 19:24 #510665
                kirbyolsen
                  Up
                  0
                  Down
                  ::

                  I am not sure and sent a p.m. asking Swede if it was possible to get it with a shorter round by less plunged depth giving a shorter crimp shank… not sure still he may have not received my P.M…

                  I also realized even it may not be worth it if setting up for that is  to involved… Heck I would actually like two mold both with mixed cavities… using the shortening the shank to give the choice of around 38g-35g-33g-30g from 2 two cavity molds… I just do not know if it would be a real pain to do or not…

                  If it is possible and not a real pain… then I would change my I want to 2 two cavity(mixed)  aluminum…

                  If not possible then am still in for one two cavity aluminum…

                  If that is the case then will  figure a way to  shorten the shank after casting… Thinking a tight fitting hole in a block to hold the round leaving the right amount protruding… then cutting with a thin sharp hot blade…

                  just trying to help ya spend your green stamps  Tom(tkerrigan)…

                  2018-05-25 at 11:57 #510666
                  AlvinYork
                  Participant
                    Up
                    0
                    Down
                    ::

                    I would hope the discussion around the crimping tool doesn’t fall on the floor. IMHO, the tools Al & Co. make are works of art. I’d certainly like to see them give the crimping tool a go.

                    2018-05-25 at 12:00 #510667
                    adamsutherland
                    Moderator
                      Up
                      0
                      Down
                      ::

                      Al is currently working on it to see if it is feasible for NOE to produce one.

                      2018-05-25 at 12:02 #510668
                      adamsutherland
                      Moderator
                        Up
                        0
                        Down
                        ::

                        Al is currently working on it to see if it is feasible for NOE to produce one.

                        It would be good if it could be used for .22WMR as well.

                        2018-05-31 at 08:53 #510670
                        teemu
                        Participant
                          Up
                          0
                          Down
                          ::

                          Can I change my order…. 3-cavity aluminium with  Lyman style HP pin and Lyman/RCBS style Top Punch. Thanks.

                          Sorry for hassle….Can I one more time change order. All same exept brass mold. Thanks

                          2018-05-31 at 15:39 #510671
                          adamsutherland
                          Moderator
                            Up
                            0
                            Down
                            ::

                            Updated.

                            2018-06-01 at 06:51 #510672
                            adeirtoncavalcante
                              Up
                              0
                              Down
                              ::

                              Can this mold be done with Hollow Base pins?

                              2018-06-01 at 06:56 #510673
                              adamsutherland
                              Moderator
                                Up
                                0
                                Down
                                ::

                                There is currently no RG option available.

                                2018-06-02 at 17:45 #510651
                                kirbyolsen
                                  Up
                                  0
                                  Down
                                  ::

                                  talked with Al and a no go on the one off stuff for now… so no shortened crimp shank… so yep staying with the 2 cavity aluminum but I do want a hollow point now…

                                  2018-06-03 at 05:27 #510669
                                  adamsutherland
                                  Moderator
                                    Up
                                    0
                                    Down
                                    ::

                                    Updated.

                                    Only two more needed, spread the word.

                                  • Author
                                    Replies
                                  Viewing 15 replies - 16 through 30 (of 44 total)
                                  1 2 3
                                  • You must be logged in to reply to this topic.