.225 WFN with a HP pin or two | NOE Bullet Moulds

This topic is empty.

Creator

Topic
2015-08-12 at 00:27 #488219
douglaspiccard
Up
-9
Down
::
Gas check version for this one. 3 cavity, aluminum blocks, and the question would be: is more than 1 HP pin possible?
cheers,
Douglas
Creator

Topic

Viewing 15 replies - 1 through 15 (of 27 total)

1 2 →

Author

Replies
2015-08-12 at 19:54 #499717
teemu
Participant
Up
0
Down
::
Yes it is possible…If You want 3-cavity You get 3 pins for HP and 3 for FT.What would be weight of that bullet? i’m interested also…
2015-08-14 at 23:31 #499718
douglaspiccard
Up
0
Down
::
Is this one:
http://noebulletmolds.com/NV/product_info.php?cPath=24&products_id=932&osCsid=s675seia9v1a39u10i06fkeh65

And, yes, the two sets of pins, with three of them flat sounds brilliant.
Cheers,
Douglas
2015-08-15 at 05:34 #499719
teemu
Participant
Up
0
Down
::
If it goes group Buy i’m in for this one.
2015-08-30 at 03:47 #499720
graemecameron
Up
0
Down
::
As my first post on this forum… hello to everyone

Definitely interested in a ~45gr HP/FN GC mould for my Brno ZKW 465 Hornet…

The online inventory shows no stock for the standard mould either… any idea when the two or three cavity .225″ 45gr FN moulds will be back in production please?
2015-09-03 at 11:19 #499721
douglaspiccard
Up
0
Down
::
Per a phone call I made to Al about a week ago these should be on the way in ~3 weeks time. Direction I got was to watch online inventory, which I plan to do. I am in for a 3-cav GC mold with its center cavity HP’d.
cheers,
Douglas
2015-10-16 at 22:36 #499722
Anonymous
Up
0
Down
::
Is this still on the rerun list?
2015-10-17 at 06:11 #499723
teemu
Participant
Up
0
Down
::
I dont think there is any RG-mold on .223/5/6… at least not inventory shows any. So if this is proposal to do so I’m in for it
2015-10-17 at 19:25 #499724
teemu
Participant
Up
0
Down
::
I’m interested Just normal WFN mold also….
2015-10-18 at 02:50 #499725
ericvandusen
Participant
Up
0
Down
::
I don’t think Al can produce molds this small in diameter in the RG format. I remember reading somewhere on this forum he needs a minimum size meplat and these tiny .22 caliber bullets are not big enough. I could be mistaken though.
2015-10-18 at 16:49 #499726
Anonymous
Up
0
Down
::
The hollow point option would be nice but for myself not a requirement. I’m thinking along the lines of my 218 bee and 22 hornets.
2015-10-22 at 12:14 #499727
k7sparky
Participant
Up
0
Down
::
I ask about the RG option on the 225 62G that was just run and Al said 22 is too small for RG
2015-10-22 at 12:58 #499728
teemu
Participant
Up
0
Down
::
Well how about that .225 45grain WFN without HP option? Is anybody interested? Just 5 buyers and it could be possible to get as inventory run. I would like to have 2-cavity 1 PB 1 GC
2015-10-23 at 02:20 #499729
amranch
Up
0
Down
::
I am very happy with the 4 cav gc that I have which has the 1 pin HP option (wooden knob type). So a HP is possible, just have a single cavity available. I believe that I saw a mold that had two of the pins setup and am about 90 % sure it was one of Al’s.
2015-10-23 at 06:48 #499730
teemu
Participant
Up
0
Down
::
I think there is no HP possibility because metplat is too small,so it would be normal mold which I mean
2015-10-23 at 22:18 #499731
Anonymous
Up
0
Down
::
I’d be in for a 5 cavity gc.
Author

Replies

Viewing 15 replies - 1 through 15 (of 27 total)

1 2 →

You must be logged in to reply to this topic.