.260-63-FN

Home › Forums › NOE Forums › NOE Archive › Historical Archive › Inventory Runs › What you would like to see ran › .260-63-FN

  • This topic is empty.
  • Creator
    Topic
  • 2017-12-07 at 17:09 #489533
    tedkramer
      Up
      -11
      Down
      ::

      I’d like to see the .260-63-FN available again, any chance of that happening?
      TSK

    • Creator
      Topic
    Viewing 13 replies - 1 through 13 (of 13 total)
    • Author
      Replies
    • 2017-12-07 at 21:50 #509830
      rsterne
      Participant
        Up
        0
        Down
        ::

        Yes, I would be interested…. You should post this in the Inventory Runs, though…. “What would you like to see run”….

        Bob

        2017-12-07 at 23:25 #509831
        Anonymous
          Up
          0
          Down
          ::

          I’d be in for a 5 cavity gas check and top punch.

          2017-12-08 at 15:57 #509832
          tedkramer
            Up
            0
            Down
            ::

            Thanks for moving this to the correct place & thanks for the interest. Hope we get enough to get it going.

            If this goes into production, put me down for a 4 cavity aluminum plain base mold.

            Ted K

            2017-12-08 at 23:47 #509833
            Full.Lead.Taco
            Keymaster
              Up
              0
              Down
              ::

              is this the bullet you are asking about or a different one?

              http://noebulletmolds.com/NV/index.php?cPath=26_180

              2017-12-09 at 03:46 #509834
              rsterne
              Participant
                Up
                0
                Down
                ::

                Yep, that is the shortened PB version of the 85 gr…. and the one I am interested in….

                Bob

                2017-12-09 at 15:27 #509835
                tedkramer
                  Up
                  0
                  Down
                  ::

                  Sorry for the incorrect designation on the bullet. I changed it on my initial post.

                  The bullet I’m interested in is the 260-63-FN.

                  Ted K

                  2017-12-09 at 19:18 #509836
                  teemu
                  Participant
                    Up
                    0
                    Down
                    ::

                    is this the bullet you are asking about or a different one?

                    http://noebulletmolds.com/NV/index.php?cPath=26_180

                    Is this mold been on Group Buy? I thought it was 63 WFN back in days and other just while ago was also WFN but GC version which isn’t option then first one… I’m confused..I thought I have all .260 molds exept that MOS-model..

                    2017-12-10 at 02:20 #509837
                    rsterne
                    Participant
                      Up
                      0
                      Down
                      ::

                      Here is the drawing of the bullet being discussed in this thread….

                      It is listed in the Store, but out of stock, so should be an Inventory Run…. I am interested in a 2-cavity with a Lyman HP pin in one…. This has been a successful airgun bullet….

                      Bob

                      2017-12-10 at 07:47 #509838
                      teemu
                      Participant
                        Up
                        0
                        Down
                        ::

                        Ok. But like a wondering I need to basement to check it out. It was back in 2015 that GB and photobucket spoils all pictures so I can’t be sure
                        http://noebulletmolds.com/smf/index.php/topic,193.0.html

                        Here is GB but without picture no help…
                        Somehow I have feeling that 2015 GB is same than just went but now new on has GC version…. Well after morning coffee i’m going to check it

                        2017-12-10 at 09:59 #509839
                        teemu
                        Participant
                          Up
                          0
                          Down
                          ::

                          Mystery solved on my part. I’ve already have that mold which Bob refer and  my memory is…is what is.  ::) Too many molds..Doing list of all but it is still unfinished.

                          2017-12-11 at 00:12 #509840
                          danielparrish
                            Up
                            0
                            Down
                            ::

                            I would be interested also. I think it would be a good one for my upcoming Cothran.257. Already have the barrel just need time to get it installed.

                            2017-12-11 at 01:58 #509841
                            jeremywright
                            Participant
                              Up
                              0
                              Down
                              ::

                              Id like a 2 cavity with hp pin

                              2017-12-11 at 02:23 #509842
                              Full.Lead.Taco
                              Keymaster
                                Up
                                0
                                Down
                                ::

                                Inventory Run Now Active sign up at the link below.  Only need 5 to get the ball rolling!

                                http://noebulletmolds.com/smf/index.php/topic,2345.0.html

                              • Author
                                Replies
                              Viewing 13 replies - 1 through 13 (of 13 total)
                              • You must be logged in to reply to this topic.