30-06 and 311365 | NOE Bullet Moulds

This topic is empty.

Creator

Topic
2014-05-31 at 20:45 #487305
darrellsteenwyk
Participant
Up
0
Down
::
Here is my results with NOE’s 311365 mould and my 30-06. I’m really pleased!
Creator

Topic

Viewing 10 replies - 1 through 10 (of 10 total)

Author

Replies
2014-05-31 at 20:47 #491034
darrellsteenwyk
Participant
Up
0
Down
::
2014-06-02 at 02:12 #491035
carrollkeatts
Up
0
Down
::
My load is abt the same in my M1 works great. Plus they just look great in a enblock.
2014-06-02 at 06:37 #491036
adamsutherland
Moderator
Up
0
Down
::
Fine bullet that performs particularly well in my M17.

I’ve been shooting it at 300yrds with N120 and it holds the 10 ring if I do my part.
2014-06-03 at 20:53 #491037
edwardmcintosh
Up
0
Down
::
I have a Savage model 12 in .308 Win that I absolutely can not get to shoot cast. I have tried many molds and many powders and the results are nill. Molds I’ve tried include 311359, 311041, 311299, 311467, group buys of 311-150 and 311-165 from the CB site and 311365 from here. I’ve sized from .308 to .311 and even tried PC’ing all the mentioned molds. I’ve tried different alloys from 50-50 WW to range scrap to straight WW to WW plus Lino. Powders from fast to slow. Anyone have any suggestions that I may not have tried.

Nighthunter
2014-06-03 at 22:49 #491038
petergallo
Up
0
Down
::
I have a Savage model 12 in .308 Win that I absolutely can not get to shoot cast. I have tried many molds and many powders and the results are nill. Molds I’ve tried include 311359, 311041, 311299, 311467, group buys of 311-150 and 311-165 from the CB site and 311365 from here. I’ve sized from .308 to .311 and even tried PC’ing all the mentioned molds. I’ve tried different alloys from 50-50 WW to range scrap to straight WW to WW plus Lino. Powders from fast to slow. Anyone have any suggestions that I may not have tried.

Nighthunter

That’s a great question, probably worth it’s own thread. With it’s own subject/title you would probably get more feedback.
2014-06-13 at 00:34 #491039
darrellsteenwyk
Participant
Up
0
Down
::
what powder are you using?
2014-07-22 at 15:03 #491040
sgt.mike
Up
0
Down
::
Blammer great group!!
I am assuming the one low was 1st shot?
2014-07-23 at 21:22 #491041
Hugh Kuhns
Participant
Up
0
Down
::
This looks like another mold for my wish list!

762sultan
2014-07-26 at 20:11 #491042
lwatson
Participant
Up
0
Down
::
That’s a fine group. Nice looking heads too.

Do yuo fast or slow-pour the pointy-heads?
2014-07-28 at 00:55 #491043
darrellsteenwyk
Participant
Up
0
Down
::
it was the last shot, I should have quit while I was ahead.

normal pour speed.
Author

Replies

Viewing 10 replies - 1 through 10 (of 10 total)

You must be logged in to reply to this topic.