311-165-RF marlin 336 30.30

Home › Forums › NOE Forums › NOE Archive › Historical Archive › General › Forum Questions / Problems › 311-165-RF marlin 336 30.30

  • This topic is empty.
  • Creator
    Topic
  • #488901
    ericcharpentier
      Up
      0
      Down
      ::

      Hello!

      I am having problems with a 311-165-RF bullet. it wont chamber in a 336 30.30 marlin made 1960.

      Anyone use this bullet?

      Help welcome.

    Viewing 8 replies - 16 through 23 (of 23 total)
    • Author
      Replies
    • #505260
      ericcharpentier
        Up
        0
        Down
        ::

        Ran into this exact issue with my 336 and Savage 99 (in 308 win) and 311-165 RF mold sized at .311 (standard lube groove). Bullet would not chamber in either rifle.
        For me, both neck/case sizer dies were short 1/4 turn. This fixed my issue for both rifles. Hopefully it’s that simple.

        What do you mean by short 1/4 turn?
        The bullet cycle well sized at .311 with a 2.355 coal. Any longer than that and bullet get stuck in chambre.

        #505261
        Anonymous
          Up
          0
          Down
          ::

          Just curious, what diameter did the bullets drop from the mold?

          Also, what powders do you have? I will run them for you at this overall length?

          Oh, one more thing. Have you tried to see if they will cycle from the magazine tube to the  chamber at this length?

          So all told, three more questions from me:

            [*]Diameter at drop[*]Powders available[*]Do they cycle?[/list]
          #505262
          ericcharpentier
            Up
            0
            Down
            ::

            Bullet drop at .314  .313
            I use IMR 3031
            The bullet cycle very well. Only thing is if loaded at more than 2.355 Bullet end up with a strong riffling mark on the nose and bullet separate from the case on ejecting leaving bullet stuck in chamber. It look like their is no free bore in that rifle.

            Remington factory 170 gr cycle and eject perfectly…

            #505263
            Anonymous
              Up
              0
              Down
              ::

              Alright, see above my question about the powder you have or want to use. I will run some data at that confined COAL.

              #505264
              ericcharpentier
                Up
                0
                Down
                ::

                I have 6 pound of IMR 3031 at hand. I use it in the 45-70 GG and want to use it in the 336RC 30.30 also.

                Thank you!

                #505265
                Anonymous
                  Up
                  0
                  Down
                  ::

                  Ooops, now I see that you answered that. My apologies!

                  Okay, I’ve tried to be as diligent as possible in recreating your cartridge here by trimming the brass (1.905″) so that I could determine the H2O capacity of the case for the load data. Here is what it all looks like.

                  GunsAndHarley_3030Win_01.jpg

                  I would consider 30.1 grains of IMR 3031 a max load. Even though I’ve been careful in all the ways I know, you are responsible for the safety of your load. Start 10% below the max, 27.0 grains.

                  Velocities for the max load should be approximately 2140 FPS at 36.9K PSI. The starting load should produce 1911 FPS at 26.3K PSI.

                  Looking forward to any reports you might have.

                  #505266
                  ericcharpentier
                    Up
                    0
                    Down
                    ::

                    This is way bewong what I would have expected.
                    Thank you again sir!

                    #505267
                    Anonymous
                      Up
                      0
                      Down
                      ::

                      You’re welcome! Best of luck.

                    Viewing 8 replies - 16 through 23 (of 23 total)
                    • You must be logged in to reply to this topic.