360-145 re-run | NOE Bullet Moulds

This topic is empty.

Creator

Topic
2014-06-13 at 01:53 #487382
charlesgilbert
Participant
Up
0
Down
::
Who would like to see this nifty little SWC make a comeback?!

Lookit all that nice wide bearing surface…. you know this one would shoot like a laser beam!

Post your interest below and check back often to see if it has gone live so you can place your actual order!

(picture borrowed from this thread http://castboolits.gunloads.com/showthread.php?242607-What-s-your-favorite-38-357-bullet-145-160-grain)
Creator

Topic

Viewing 14 replies - 1 through 14 (of 14 total)

Author

Replies
2014-06-13 at 02:06 #491733
davidshimko
Participant
Up
0
Down
::
Im in for a 4 cav mold
2014-06-14 at 03:39 #491734
victorjones
Participant
Up
0
Down
::
I’m interested. Tony
2014-06-17 at 00:38 #491735
davidswann
Participant
Up
0
Down
::
A HP version would be sweet, then I’d be interested.

Sorry, I really want an NOE 358156 HP in .360 diameter. Just need something a little heavier than the 360-145.
2014-06-21 at 02:49 #491736
thomasgarcia1
Participant
Up
0
Down
::
Beagle,

What was the weight and with what alloy (the ones pictured).

It looks like a mini 45-270-SAA, at least on my iPhone best as I can tell.

I’d be interested depending on which options available and cost.
2014-06-21 at 03:00 #491737
charlesgilbert
Participant
Up
0
Down
::
I dunno. I’d have to guess it weighed 145gr, but they were cast by GLL, so I can’t really say.
I posted the link above, where I borrowed the picture from. I don’t have one of these molds.
2014-06-25 at 20:30 #491738
SwedeNelson
Keymaster
Up
0
Down
::
We have this one back in stock
http://noebulletmolds.com/NV/product_info.php?cPath=35&products_id=855&osCsid=11np42t40gf3lmi08gfeq7s0b2

Bullet maker, maker
Al nelson
2014-06-25 at 23:08 #491739
wardolson
Up
0
Down
::
I see this referred to as 145 gr and 150 gr. I mostly use a 50/50 mix of COWW/pure lead. Where will I come in for weight? How about if I go with the HP and cup point version? Where will they fall as to weight. I’m pretty well set in the 150 to 170 grain area and would like to take a noticable step lighter in going with this mould.

Thanks
ward
2014-06-26 at 00:46 #491740
SwedeNelson
Keymaster
Up
0
Down
::
WARD O

Estimated weight with wheel weights
With FN 154Gr., HP 140Gr., Cup Point 151Gr.

I hope this helps
Bullet maker, maker
Al Nelson
2014-06-26 at 02:37 #491741
charlesgilbert
Participant
Up
0
Down
::
We have this one back in stock

And in brass!!!! Order placed!
Thank you!!!
Chuck
2014-07-15 at 16:07 #491742
chuckvatnsdal
Up
0
Down
::
Glad to see the interest in this one again! I use this as my standard 38Special boolit— unless you use a carbine that requires a rounder profile, this is the one to go with— accuracy is unbelievable!

Chuck 358wcf
2014-09-25 at 14:44 #491743
jeffyoung
Participant
Up
0
Down
::
358wcf, what charge of what powder are you using? Thanks, LBS
2014-09-26 at 04:24 #491744
mriman
Up
0
Down
::
Any chance with a HP option?
Thinking about it.
Leadmelter
MI
2014-09-26 at 14:29 #491745
SwedeNelson
Keymaster
Up
0
Down
::
IN STOCK

We have this one in stock
http://noebulletmolds.com/NV/product_info.php?cPath=35&products_id=858
or you can see them all here – about the middle of the page
http://noebulletmolds.com/NV/index.php?cPath=35&osCsid=frithg5apeea7dsa5705cjprq4
It cast at 150gr. so we have changed the designation but it is the same bullet
Have some RG’s too!

I use them in a Colt Diamond Back that shoots them like a laser – dead on
Fun little bullet and a explosive HP

Bullet maker, maker
Al Nelson
2014-09-27 at 04:07 #491746
mriman
Up
0
Down
::
Yes I found them and a 2 cavity RG2 is in the mail
Thanks
mriman
MI
Author

Replies

Viewing 14 replies - 1 through 14 (of 14 total)

You must be logged in to reply to this topic.