402 150Gr. FN RG4 cavity HP …Best 40 mold out there but has been unavailable.

Home › Forums › NOE Forums › NOE Archive › Historical Archive › Inventory Runs › What you would like to see ran › 402 150Gr. FN RG4 cavity HP …Best 40 mold out there but has been unavailable.

  • This topic is empty.
  • Creator
    Topic
  • #488589
    danielpoeder
      Up
      -10
      Down
      ::

      402 150Gr. FN RG4 cavity HP.  This is one of the best 40 cal molds out there anywhere.  Too bad no one makes this and NOE has left this a 0 inventory for quite some time.  Light weight round flat point 40’s are non existant except for special order and then they are usually in 2 cavity.

      Many of my 40 autos shoot lighter (<180gr) bullets very accurately.  My lead stock goes further also....... 

    Viewing 15 replies - 16 through 30 (of 50 total)
    • Author
      Replies
    • #502930
      randyren
        Up
        0
        Down
        ::

        Count me in, 4 cavity RG4 402-150

        #502931
        chriswelch
        Participant
          Up
          0
          Down
          ::

          4 cav plain base  hp aluminum would be great and the lighter weight would be great for plinking and general training.

          And it would let me retire my finicky lee TL401-175-SWC  Never liked the way the sprue cutter was set up on these :(

          #502932
          AlvinYork
          Participant
            Up
            0
            Down
            ::

            I think it’s 5 for a stock run. We’re ahead of the game.

            #502933
            charlesbachner
              Up
              0
              Down
              ::

              What’s the next step for getting Al to produce now that we have more than enough for a stock run?

              #502934
              AlvinYork
              Participant
                Up
                0
                Down
                ::

                Usually dromia interfaces with Al. For some reason he’s not involved in this one. Perhaps you could send Al a PM and let him know we’re good to go.

                #502935
                SwedeNelson
                Keymaster
                  Up
                  0
                  Down
                  ::

                  Will see what we can get done.
                  Still behind some so it may take a week or so to get it listed.

                  Thanks for the interest
                  Bullet maker, maker
                  Al Nelson

                  #502936
                  charlesbachner
                    Up
                    0
                    Down
                    ::

                    Yay!!!!!

                    #502937
                    AlvinYork
                    Participant
                      Up
                      0
                      Down
                      ::

                      Apologies, StuBach, I’m plagiarizing your “I want” list
                      I went through and added the particulars of the wants.

                      MANY OF YOU did not specify base type. It would probably be good to do that so Al has a better idea of what to make

                      rren3 402 150g FN RG4 PB
                      Meadmkr 402 150g FN RG4 PB
                      Elkins45 402 150g FN RG4 GC? PB?
                      marlin39a 402 150g FN  GC
                      wasalmonslayer 402 150g FN  PB
                      Mountain man  402 150g FN RG4 PB Brass
                      Dragon813gt 402 150g FN RG4? GC? PB?
                      AlvinYork 403 150g FN RG4 GC (402 ok also)
                      Stubach 403 150g FN RG4 PB (402 ok also)
                      Dspoeder 402 150g FN RG4 GC? PB?
                      Paper Puncher 402 150g FN RG4 PB

                      I hope this helps Al a bit.

                      I’m looking forward to casting up a mess of these and blasting them downrange!

                      #502938
                      brigettecuneo
                      Participant
                        Up
                        0
                        Down
                        ::

                        Thank you for setting the list all together.
                        I’m hoping this molds becomes my girl’s favorite new recipe for her pistol. I would like a 4 cavity hollow point brass mold for the 40 s and w in the plain base version with the extra pins for the flat nose please.
                        Also, I had question, is everyone going to use a flat base seater stem? I only have a round stem, so I was curious as to where folks are getting their’s, or what they are using. We have lee dies, so I was not sure if I needed specific seater die stems.Thank you for the help, and I apologize for side tracking the post.

                        #502939
                        AlvinYork
                        Participant
                          Up
                          0
                          Down
                          ::

                          Ok, I updated the list.
                          The other pins, flat and cup usually, are part of the deal.
                          My seating die is also a Lee. I don’t recall off hand what the seater stem is. I just seat them with whatever is in there. So, I don’t think you’ll need another stem. Unless your alloy is soft enough where it could be molded by the stem.

                          #502940
                          charlesbachner
                            Up
                            0
                            Down
                            ::

                            Alvin, no problem on using the list. My apologies for not doing it before. New to NOEs GB process so figured the particulars waited till it went active. Will your list be transitioned over to the active buy when it goes live or do we need to sign up again?

                            #502941
                            AlvinYork
                            Participant
                              Up
                              0
                              Down
                              ::

                              StuBach, my experience has been that a new topic is started over in the Active run forum and everyone posts their “I want”s again. At this point the list is mainly for Al to get an idea as to what to make and how much. The one in the Active run forum is what Al makes sure he has on hand for when the inevitable order comes in.
                                That’s my understanding anyway.

                              #502942
                              brigettecuneo
                              Participant
                                Up
                                0
                                Down
                                ::

                                StuBach, my experience has been that a new topic is started over in the Active run forum and everyone posts their “I want”s again. At this point the list is mainly for Al to get an idea as to what to make and how much. The one in the Active run forum is what Al makes sure he has on hand for when the inevitable order comes in.
                                  That’s my understanding anyway.

                                I’m also new to the forums and how it all works. I appreciate the heads up on what the next step is. I will keep an eye out for it on the new thread. Thank you gentlemen

                                #502943
                                randyren
                                  Up
                                  0
                                  Down
                                  ::

                                  Put me down for one also.  402-150 FN RG4 HP mould

                                  #502944
                                  AlvinYork
                                  Participant
                                    Up
                                    0
                                    Down
                                    ::

                                    List updated

                                  Viewing 15 replies - 16 through 30 (of 50 total)
                                  • You must be logged in to reply to this topic.