450 Bushmaster Group Buy Discussion

This topic is empty.

Creator

Topic
2019-04-07 at 22:21 #489907
julianbownes
Participant
Up
0
Down
::
Greetings fellow casters,

This one is currently in the run schedule to run in the next two or three weeks.

Final Design Below

Link to the buy on Cast Boolits:

http://castboolits.gunloads.com/showthread.php?380350-CLOSED-NOE-450BM-C-285-grain-(Cast)-for-450-Bushmaster-45-Colt-454-Casull

This has already met minimum so get on if you have not already signed up on Cast Boolits

NOE Sign Ups Only:

1.
2.
3.
4.
5.
Creator

Topic

Viewing 15 replies - 16 through 30 (of 30 total)

← 1 2

Author

Replies
2019-04-25 at 18:26 #511713
Full.Lead.Taco
Keymaster
Up
0
Down
::
I talked to Al to see if he could run this one in gas check config, plain base config, and a grooveless PB (not gas check) config. He said he could do that.

Alright, what about this?
2019-04-27 at 15:39 #511714
Hugh Kuhns
Participant
Up
0
Down
::
Would it be possible to have a mould made with 2 PB cavities with lube grooves and 2 cavities with no lube grooves for powder coating?

762sultan
2019-04-28 at 22:31 #511715
Full.Lead.Taco
Keymaster
Up
0
Down
::
That definitely sounds interesting, I will check with Al and get back.

Would it be possible to have a mould made with 2 PB cavities with lube grooves and 2 cavities with no lube grooves for powder coating?
2019-04-29 at 16:16 #511716
Full.Lead.Taco
Keymaster
Up
0
Down
::
I asked Al about this and he said that he would not be able to do it at this time.

Would it be possible to have a mould made with 2 PB cavities with lube grooves and 2 cavities with no lube grooves for powder coating?
2019-04-29 at 18:11 #511717
Hugh Kuhns
Participant
Up
0
Down
::
I might have to buy 2 moulds…one for lube grooves and one without.

762sultan
2019-04-30 at 03:27 #511718
Full.Lead.Taco
Keymaster
Up
0
Down
::
I think I might buy a 450 bushmaster upper just to test out this bullet/mould.

I might have to buy 2 moulds…one for lube grooves and one without.
2019-04-30 at 03:33 #511719
Full.Lead.Taco
Keymaster
Up
0
Down
::
Hollow point pin wise, do we want a deep hollow point pin and a shallow cup point?
2019-04-30 at 20:06 #511720
Hugh Kuhns
Participant
Up
0
Down
::
I plan on using this for Eastern black bears and deer so a bullet that penetrates and doesn’t ruin a lot of meat or destroy the pelt is what I am looking for. A small HP would work for me.

762sultan
2019-05-05 at 22:30 #511721
julianbownes
Participant
Up
0
Down
::
I think I might buy a 450 bushmaster upper just to test out this bullet/mould.

I might have to buy 2 moulds…one for lube grooves and one without.

Save some money and get the Bear Creek Arsenal Upper Complete. Shoots better than my Ruger at a fraction of the cost.
2019-05-06 at 15:00 #511722
Full.Lead.Taco
Keymaster
Up
0
Down
::
I will definitely take a look. Bluejay, so are you good with one deeper hollow point and one cup point?

Save some money and get the Bear Creek Arsenal Upper Complete. Shoots better than my Ruger at a fraction of the cost.
2019-05-07 at 16:45 #511723
AlvinYork
Participant
Up
0
Down
::
Interesting. I think I might try this in the 460 Rowland if it keeps it’s maximum weight <= 300.
I’ll pick up two moulds. One for HP and one for solid.
2019-06-05 at 01:05 #511724
julianbownes
Participant
Up
0
Down
::
Please see final design and sign up if you haven’t already signed up on Cast Boolits.
2019-06-05 at 20:26 #511725
Packy
Participant
Up
0
Down
::
I would like aluminum rg4 g.c. 452 pcoop63 at gmail dot com
2019-06-07 at 12:29 #511726
AlvinYork
Participant
Up
0
Down
::
I haven’t seen the castboolits sign up, sounds like it’s closed now, but I would like, if possible, to be put down for 2 of these : both PB with one Brass four cav HP and the other one 5 cav Aluminum solid.
2019-06-07 at 19:19 #511727
julianbownes
Participant
Up
0
Down
::
Sir. Either PM your email sign up at the link on page 1.
Author

Replies

Viewing 15 replies - 16 through 30 (of 30 total)

← 1 2

You must be logged in to reply to this topic.