453-213-RF and 453-187-HP -12- GB229 (6/9/15)

Home › Forums › NOE Forums › NOE Archive › Historical Archive › Group Buys › Archived Buys › 453-213-RF and 453-187-HP -12- GB229 (6/9/15)

  • This topic is empty.
Viewing 15 replies - 31 through 45 (of 53 total)
  • Author
    Replies
  • #498122
    Elkins45
    Spectator
      Up
      0
      Down
      ::

      Put me down for an aluminum RG4 and a Lyman top punch.

      I wish I had known about this one on Sunday–I could have combined it with my 35xcb order and saved $6 for shipping :) I think this one will put me in the >$1K club.

      #498123
      adamsutherland
      Moderator
        Up
        0
        Down
        ::

        List updated.

        #498124
        georgekahn
        Participant
          Up
          0
          Down
          ::

          I want it:  453-187-HP as a RG 4 cavity brass, plus a Lyman t p, plus set of blank pins.
          Thanks.    george

          #498125
          timfoster
          Participant
            Up
            0
            Down
            ::

            Please note that i would prefer Aluminium instead of Brass If possible. I did make a note in my original post.
            Tim (Jeepyj)

            #498126
            adamsutherland
            Moderator
              Up
              0
              Down
              ::

              Please note that i would prefer Aluminium instead of Brass If possible. I did make a note in my original post.
              Tim (Jeepyj)

              You are already down for an aluminium mould.

              I you ever need to change your order then don’t amend the original post put a new post in the thread for me to pick up on, I don’t have the time or the inclination to re-read every post every time I open a thread.

              #498127
              adamsutherland
              Moderator
                Up
                0
                Down
                ::

                List updated.

                #498128
                ronaldross
                Participant
                  Up
                  0
                  Down
                  ::

                  I want an RG 4 aluminum w/ Lyman top punch. 

                  hicard21atoutlookdotcom

                  #498129
                  adamsutherland
                  Moderator
                    Up
                    0
                    Down
                    ::

                    List updated.

                    #498130
                    nathanparker
                    Participant
                      Up
                      0
                      Down
                      ::

                      I would like an RG4 aluminum, please.

                      #498131
                      johnalbert
                      Participant
                        Up
                        0
                        Down
                        ::

                        I should have been more clear..  The RG2 2 cavity HP in brass is what I want.  With top punch and lube.

                        #498132
                        thomasparsons
                        Participant
                          Up
                          0
                          Down
                          ::

                          If I am not too late, please add me for a RG2 in Aluminum.

                          Thanks,
                          Doc

                          #498133
                          adamsutherland
                          Moderator
                            Up
                            0
                            Down
                            ::

                            List updated.

                            #498134
                            jonathanjohnson
                              Up
                              0
                              Down
                              ::

                              Very excited for this mould!  Thanks again!

                              #498135
                              Intel6
                              Participant
                                Up
                                0
                                Down
                                ::

                                I have yet to try out an RG mould from Al but it looks like this will be the one that does it,  can’t resist.

                                RG2 in Aluminum to cut my teeth on.

                                Thanks,

                                Neal in AZ

                                #498136
                                adamsutherland
                                Moderator
                                  Up
                                  0
                                  Down
                                  ::

                                  List updated.

                                Viewing 15 replies - 31 through 45 (of 53 total)
                                • You must be logged in to reply to this topic.