Looking for NOE owners of…..

Home › Forums › NOE Forums › NOE Archive › Historical Archive › General › Forum Questions / Problems › Looking for NOE owners of…..

  • This topic is empty.
  • Creator
    Topic
  • #488893
    eldonmcwilliams
      Up
      0
      Down
      ::

        I’m looking to connect with any owners that are using the NOE 279-124-FN 2 cavity GC mold – OR – the NOE 266-125-FN 2 cavity GC (6.5 Grendel) mold.  I am awaiting a production run and would like to get hold of some to be sure this is what I want.
        I’d also like input as to the mold use. I just got thru 3 1/2 hours of casting with my first LEE mold…….ALSO MY LAST LEE MOLD! I have been casting for many years and this is the first time I have ever had a 34% (by actual count) cull rate during any of my casting sessions.
        Please leave a PM.
      Thanks.
      EKM

    Viewing 6 replies - 1 through 6 (of 6 total)
    • Author
      Replies
    • #505191
      Hugh Kuhns
      Participant
        Up
        0
        Down
        ::

        First off I don’t have the mould you are looking for. But I can point you to some help with your brand X mould. There is a section at the bottom of the forum  called” Using NOE moulds that has a sub-section that has tips for using a new mould. These tips will guide you through the steps for properly preparing a mould for use. They are pretty much tried and true, and they work well for aluminum molds as well as iron and brass. These tips are a collection of trial and error and are strongly recommended by many veteran casters. I invite you to buy a NOE mould and step up to a different level of mould. Nothing wrong with brand X but if you talk to other casters they will tell you the same. Hopefully some forum member will step in and offer you a few sample bullets to let you continue your quest.

        762sultan

        #505192
        eldonmcwilliams
          Up
          0
          Down
          ::

              Thankx Sultan. I have worked out those problems but am still left frustrated by the first time experience. I own a couple of NOE molds I had made for some WWII rifles I had. They have worked well from  the git-go with none of the Brand X problems. I found no difference between aluminum or steel at that time.
              I’m hoping someone sees my post on the 6.5 & 6.8 molds so I can get some samples. NOE is the only place to make a usable 6.5 bullet in a weight that is actually usable in my 6.5 Grendel and 6.5 MPC.
              Thankx again!
          EKM

          #505193
          Hugh Kuhns
          Participant
            Up
            0
            Down
            ::

                    Go to  “archived group buys ” and look on page 5 and it shows the group buy that ran summer of 2015.  It lists those who bought that mold on the group buy and maybe you could contact one of those people and strike a deal for some bullets. They might not have any that are unsized or they may have a whole big box full.

            762sultan

            #505194
            eldonmcwilliams
              Up
              0
              Down
              ::

              THANKS AGAIN! Great idea……I didn’t think of that. i will give a try tonight.
              Thanks,
              EKM

              #505195
              AlvinYork
              Participant
                Up
                0
                Down
                ::

                I own both a NOE 279-124-FN and a NOE 266-125-FN, but in 5 cav and 4 cav respectively and both plain base. If I remember correctly the stuff that I cast these with is rather hard (lots of tin and antimony), 15 to 19 BHN. I know the PB may be a dealbreaker but if that’s ok with you I can send you some samples. If you’re interested send me a PM with your details and I’ll hand them off to Uncle Sam’s Postal Service.

                #505196
                Full.Lead.Taco
                Keymaster
                  Up
                  0
                  Down
                  ::

                  I have the grendel mold, but have not cast with it yet.  Send me a pm with some details if you need me to do something.

                Viewing 6 replies - 1 through 6 (of 6 total)
                • You must be logged in to reply to this topic.