- This topic is empty.
-
Topic
-
SwedeNelson
NOE 257-65-FN (Bob’s Boat Tail)
We will be running this like a inventory runhttp://noebulletmolds.com/photos/albums/257-65-FN-BT-/257-65-FN_-BT-__65_gr_Sketch.Jpg%5B/img%5D
We will offer this one .250 /.252, .253 /.255 and .257 /.259
Calculated to stabilize in a 14″ twist barrel.We will be running 2 cavity, 2 cavity Brass, 3 cavity, 4 cavity, 4 cavity Brass, 5 cavity Bevel Base only.
We will offer a Lyman type single pin Hollow Point system in one cavity of any of the above moulds.
Top punch, wrenches and sprue lube are extras now if you want themAll moulds will be assumed to be Aluminum unless Brass is requested!
Prices will be our standard website prices ( http://www.noebulletmoulds.com )
2 cavity $79.00
2 cavity Brass $101.00
3 cavity $86.00
4 cavity $92.00
4 cavity Brass $114.00
5 cavity $99.00Lyman type single pin Hollow Point $35.00
Lyman/RCBS style Top Punch $5.00
Saeco style Top Punch $7.50
Mould Wrenches / Sprue Lube $2.50Will run this as soon as we get 10 signed up and we get the tooling in.
Will have them listed on our website as a inventory item as soon as we have them ran
So you can use Pay-Pal, Credit Card or Check / Money order
Post a “I want” and receive a 15% discount off the website
We will PM a discount code for you to use at check outIf you have question – Visit our website or PM me
Thanks
Swede Nelson
SwedeNelson-
Replies
-
List of orders
1 rsterne 2 cavity aluminium HP 0.257″
2 tnt76 3 cavity aluminium HP 0.257″
3 Jc1234 3 cavity aluminium 0.257″
4 grumpy 2 cavity aluminium HP 0.257″
5 owen 2 cavity aluminium 0.250″
6 deadguy 2 cavity aluminium 0.257″
7 Clifford 2 cavity aluminium HP 0.257″
8 rsterne 2-cavity aluminium HP 0.250″
9 tnt76 2 cavity aluminium HP 0.253″
10 Christopher 2 cavity aluminium HP 0.250″
11 grumpy 2 cavity aluminium 0.257″
12 wolfiek 2 cavity aluminium 0.257″
13 wolfiek 2 cavity aluminium 0.253″
14 enazle 2 cavity brass 0.253″
15 Jusadbellum 2 cavity brass HP 0.250″
16 Jusadbellum 2 cavity brass 0.257″
17 jeremy1982 2 cavity aluminium HP 0.257″
18 Bullfrog 2 cavity aluminium HP 0.253″
19 teemu 2 cavity aluminium .253″Thanks for the orders
Bullet maker, maker
Al Nelsonrsterne
Jc1234
Thanks very much to Al for deciding to offer this bullet in three sizes…. The choices available will now allow it to be used in airgun barrels as well as the standard .257 cal PB size…. The profile will be identical for all three sizes, allowing one tool to be used for the machining…. so all the diameters will vary by the same amount, and for the .250 and .253 cal the bullet will be 0.014″ shorter, with an overall length of 0.500″…. This length reduction and slight increase of the boattail base diameter (for the 0.250″ and 0.253″ versions) will allow them to stabilize in a slightly slower twist…. The 0.253″ should work great in the Green Mountain barrel with a 15.5″ twist, as used on the Marauder…. while the 0.250″ will of course be fine in the commonly available TJ’s .25 ACP replacement liner, with it’s 14″” twist…. The 0.250″ will weigh about 60 gr. as a FN solid, and the 0.253″ about 62 gr…. with the HP versions 3 gr. lighter, of course….
Please put me down for a 0.250″ 2-cavity aluminum with HP pin, in addition to my order for the 0.257″ version….
Bob
rsterne
tnt76
Jc1234
davidgoldstein
adamsutherland
owencoors
thomasraether
kurtismartin
- You must be logged in to reply to this topic.