257-65-FN (Bob’s Boat Tail) (19)

Home › Forums › NOE Forums › NOE Archive › Historical Archive › Group Buys › Archived Buys › 257-65-FN (Bob’s Boat Tail) (19)

  • This topic is empty.
Viewing 15 replies - 16 through 30 (of 52 total)
1 2 3 4
  • Author
    Replies
  • 2017-01-30 at 16:30 #504735
    adamsutherland
    Moderator
      Up
      0
      Down
      ::

      All assumed to be and entered as 0.257″ up ’till entry 8 when the other options were available.

      2017-01-30 at 16:40 #504736
      rsterne
      Participant
        Up
        0
        Down
        ::

        Thanks, dromia…. I PM’d everyone else to make sure they are aware of the new sizes…. in case they need to change or add to their order….

        Bob

        2017-01-30 at 20:58 #504737
        tnt76
          Up
          0
          Down
          ::

          PM Read Bob, thanks.

          Could I change my original .257 order from a 2 cav to 3 cav alum.

          And could I add a .253 2 cav alum to the list.

          Both moulds with a HP Pin in one cav.

          Thanks

          2017-01-30 at 21:50 #504738
          Christopher
            Up
            0
            Down
            ::

            I would like a 2 cavity aluminum  in the .250″ diameter with a HP pin.

            Thank you

            2017-01-31 at 05:53 #504739
            adamsutherland
            Moderator
              Up
              0
              Down
              ::

              List updated.

              Al notified.

              2017-01-31 at 07:42 #504740
              owencoors
                Up
                0
                Down
                ::

                I still want the aluminum 2-cavity FN in .257, please.

                2017-01-31 at 18:36 #504741
                davidgoldstein
                  Up
                  0
                  Down
                  ::

                  Please add a

                  2 cav alum FN

                  to my existing order. Please make both for the TJ barrel which I believe bob said is .250 ?

                  Thanks
                  David

                  2017-02-01 at 00:07 #504742
                  adamsutherland
                  Moderator
                    Up
                    0
                    Down
                    ::

                    List updated.

                    2017-02-01 at 06:17 #504743
                    davidgoldstein
                      Up
                      0
                      Down
                      ::

                      Just to clarify. I need the version for TJ 14″ barrel. Thanks

                      David

                      2017-02-01 at 07:51 #504744
                      adamsutherland
                      Moderator
                        Up
                        0
                        Down
                        ::

                        Suggest that you PM rsterne if uncertain about the diameter you need.

                        2017-02-02 at 11:09 #504745
                        owencoors
                          Up
                          0
                          Down
                          ::

                          Grumpy, there are two TJ liners that will work with these. One is .250″ (.25 ACP) and one is .257″ (.25/35.)

                          Admin, Please change my order to an aluminum 2-cavity FN in .250″, please.

                          2017-02-02 at 14:06 #504746
                          adamsutherland
                          Moderator
                            Up
                            0
                            Down
                            ::

                            Updated.

                            2017-02-02 at 16:44 #504747
                            davidgoldstein
                              Up
                              0
                              Down
                              ::

                              Spoke to Bob, I would like both my moulds to be for the 14″ TJ  0.257 barrel.

                              Thanks
                              David

                              2017-02-03 at 06:32 #504748
                              adamsutherland
                              Moderator
                                Up
                                0
                                Down
                                ::

                                Updated.

                                2017-02-06 at 10:43 #504749
                                wolfiek
                                  Up
                                  0
                                  Down
                                  ::

                                  Hi!

                                  I would like an aluminum 2-cavity mold for TJ .257 barrel (1/14″ Twist)

                                  Thanks in advance

                                  Best Regards!

                                • Author
                                  Replies
                                Viewing 15 replies - 16 through 30 (of 52 total)
                                1 2 3 4
                                • You must be logged in to reply to this topic.