- This topic is empty.
-
Topic
-
rhbrink-
Replies
-
Anonymous
Mike B
Reading through Bob’s discussions regarding these molds, he states the only difference between the Hunter and Magnum is the length and that the tooling is the same. Would it require anything additional, or could orders for both molds be run consecutively for buyers wanting both?Jonathan
If that ends up being an option I’d certainly be willing to throw my name into the hat there for that magnum mold as well.
Mike B.
AS I said previously You will have to call Al on that and get his opinion on that.
Years ago I suggested that Al could use the tooling from a 266 mould design to make a 260 mould design…
All went well until I requested that the GC shank be shortened by about .010… this could have easily been done by surface finishing the mold body to remove the .010 GC skirt length after the the original tooling had been used to make the slightly smaller diameter bullet mould.
At that point Al said that what I wanted was a change in tooling that could not be accomplished with the original tooling.
Not to start an argument nor dispute in any way shape nor form of what you are saying… I have scanned the two mould dimensional sketches and attached said scan to this reply as a jpg that I believe will be accepted by the NOE forum attachment parameters…
The HB pins are of different dimensional parameters, & as has been noted the pellet skirt is different… You need to look at the two drawings and decide for yourselves and then talk to Al…
Almost certainly the TPs will be interchangeable …
rsterne
I have added you to my unofficial tracking listing on this subject.
What I am seeing in my daily searches on the store forum … at the moment are mould handles and sizing die sets being worked on and the amounts being updated.1. rhb 300-46-RF-CC4 RG2 Aluminum 4-15-21
2. awilde 300-46-RF-CC4 RG4 Aluminum 4-16-21
3. Trirman 300-46-RF-CC4 RG4 Aluminum 4-16-21
4. SqrlHntr 300-46-RF-CC4 RG4 Aluminum 4-16-21
5. SqrlHntr 300-46-RF-CC4 RG4 Aluminum 4-16-21
6. Youngbuck3006 300-46-RF-CC4 RG4 Aluminum 4-21-21
7. Trirman 300-46-RF-CC4 RG4 Aluminum 4-22-21
8. Phillip 300-46-RF-CC4 RG4 Aluminum 4-23-21
9. Heath 300-46-RF-CC4 RG4 Aluminum 4-24-21
10. basscop2 300-46-RF-CC4 RG2 Aluminum 5-14-21
11. MEmeMEme1 300-46-RF-CC4 RG4 Aluminum 6-04-21
12. Killing Time 300-46-RF-CC4 RG4 Aluminum 6-10-21Gentlemen,
There appears to be stock on the 300-46-RF shelves… at this moment…https://noebulletmolds.com/site/product-category/308-311/300-46-rf-cc4-hunter-pellet/
Get them while they are hot…
You will most probably have to talk to Al about a group buy discount… and its current status…
Here once again is the link to the forum inventory run group buy that was apparently posted by Al on July 23rd 2016. https://noebulletmolds.com/smf/index.php/topic,1624.0.html
Here also is the text from that posting text with a bit of intel in bold print included in that posting that may tend to answer your question.
HOW WE RUN OUR INVENTORY BUYS
Inventory Buys start in the “What you would like to see ran” section
Moulds that are listed in inventory but out of stock are posted to see what the interest
is and start to get a idea of what kind of orders can be expected.We still reserve the right to run any inventory item at any time – and this does not make
the item eligible for any kind of a discount at this time.After a item has shown enough interest It is moved from the “What you would like to see ran”
section to the “Active Inventory Buy” section. This is were you place your order and can
check on the progress. When a buy gets 5 orders, it is scheduled to go to the shop.
At this time a last call is issued too. As soon as we can get it worked in to the schedule the buy is
ran and it is moved to the “Closed Inventory Buys” section. We try to do this in a timely manner.As soon as a run comes off the mill it is posted on our website and a PM is sent with
ordering instruction and a discount code. We offer a 15% discount on inventory runs through
our forum.If a run does not get 5 orders or it takes longer than 6 months to get 5 orders
it will be evaluated at that time and either will be closed or extended another 6 months.
« Last Edit: March 26, 2017, 16:59:12 by cornmastah »Jonathan Flammer
Mike B.
I can’t get the website to let me order this mold. I had a running order of items I was going to order, and the system will not let me add or delete them from my cart. I can build my order if I’m not signed in, but once I sign in, the system returns my cart to the previous order and will not allow changes.Jonathan
jimshuler
youngbuck3006
You will most probably have to call, Email, or PM Al, & also copy the forum administrator William to ask what is going on with the store website and your particular account.I am sorry that I cannot give you a better answer your query…
My account just let me do what you just tried, & said that the forum would not let you do… with your account… So it may be only your account that is affected…There was a query this AM by rhb about an inventory discount, Al posted the mould inventory run guidelines in July of 2016… that may have possibly some effect on your query.
Maybe that is what is… possibly going on… ?I’m just a forum member … as you are, so I regret that I have nothing to do with the forum administration, nor the store forum’s administration.
Sorry, … I know that this is not much of a help…
It is what it is…
Take Care & Stay Safe…
Mike B.
Mike B.
rsterne
jimshuler
Jonathan Flammer
jefferyfloyd
- You must be logged in to reply to this topic.