300-68-FN (Bob’s Boat Tail) -11- GB276

Home › Forums › NOE Forums › NOE Archive › Historical Archive › Group Buys › Archived Buys › 300-68-FN (Bob’s Boat Tail) -11- GB276

  • This topic is empty.
  • Creator
    Topic
  • 2016-01-09 at 18:07 #488536
    SwedeNelson
    Keymaster
      Up
      0
      Down
      ::

      NOE 300-68-FN (Bob’s Boat Tail) 
      We will be running this like a inventory run

      We will be offering this one .300″/.302″ and .303″/.305″ diameter

      We will be running 2 cavity, 2 cavity Brass, 3 cavity, 4 cavity, 4 cavity Brass, 5 cavity, RG2 cavity, RG2 cavity Brass, RG4 cavity,
      RG4 cavity Brass. Bevel Base only.
      Top punch, wrenches and sprue lube are extras now if you want them

      All moulds will be assumed to be Aluminum unless Brass is requested!

      Prices will be our standard website prices ( http://www.noebulletmoulds.com )
      2 cavity $79.00
      2 cavity Brass $101.00
      RG2 cavity $103.00
      RG2 cavity Brass $125.00
      3 cavity $86.00
      4 cavity $92.00
      4 cavity Brass $114.00
      RG4 cavity $133.00
      RG4 cavity Brass $155.00
      5 cavity $99.00

      Lyman/RCBS style Top Punch $5.00
      Saeco style Top Punch $7.50
      Mould Wrenches / Sprue Lube $2.50
      RG2 blank pin set $4.50
      RG4 blank pin set $9.00

      Will run this as soon as we get 10 signed up and we get the tooling in.
      Will have them listed on our website as a inventory item as soon as we have them ran
      So you can use Pay-Pal, Credit Card or Check / Money order
      Post a “I want” and receive a 15% discount off the website
      We will PM a discount code for you to use at check out

      If you have question – Visit our website or PM me

      Thanks
      Swede Nelson

    • Creator
      Topic
    Viewing 15 replies - 16 through 30 (of 72 total)
    1 2 3 4 5
    • Author
      Replies
    • 2016-01-12 at 18:04 #502510
      traviswhitney
        Up
        0
        Down
        ::

        3 cavity aluminum please

        2016-01-12 at 19:11 #502511
        adamsutherland
        Moderator
          Up
          0
          Down
          ::

          List updated.

          2016-01-24 at 14:23 #502512
          maxgarnett
            Up
            0
            Down
            ::

            When the sales are closed will the store site have a air gun section to buy from. I have found the store site hard to use . Then again I am a PC challenged senior.  Stikys !!!??could not find them. Only stiky I’ve gotten to is the food on my key board thingy.
            Thanks for any help when the time to settle up comes.

            2016-02-01 at 22:26 #502513
            shaunsharpton
              Up
              0
              Down
              ::

              So can I get a 4 cavity RG aluminium mold with handles, lube, any thing else? How many do we need? I’m ready to pay now.

              2016-02-02 at 07:32 #502514
              adamsutherland
              Moderator
                Up
                0
                Down
                ::

                List updated.

                Payment when notified with the discount code when the moulds are cut.

                2016-02-02 at 16:33 #502515
                rsterne
                Participant
                  Up
                  0
                  Down
                  ::

                  So is that 2 moulds for Gr8gorilla, or a change to an RG4?…. Not that I care, I just noticed he was down twice….

                  Bob

                  2016-02-03 at 07:31 #502516
                  adamsutherland
                  Moderator
                    Up
                    0
                    Down
                    ::

                    From reply No.19 he hasn’t asked to change his order, it reads that he wants an RG as well so down for two moulds

                    If this is not the case then he will need to be a bit clearer about his wants so that I can amend accordingly.

                    2016-02-19 at 13:21 #502517
                    maxgarnett
                      Up
                      0
                      Down
                      ::

                      I spoke with rsterne about the flex , is this the mold modification for that app. curious?

                      2016-02-19 at 16:06 #502518
                      rsterne
                      Participant
                        Up
                        0
                        Down
                        ::

                        Yes, this bullet should be great in the FLEX….

                        Bob

                        2016-02-20 at 00:22 #502519
                        maxgarnett
                          Up
                          0
                          Down
                          ::

                          Thank you

                          2016-02-20 at 15:29 #502520
                          shaunsharpton
                            Up
                            0
                            Down
                            ::

                            I really would like this thing to fire but I think I need just one mold. Please modify me to an RG4 with pins, sprue lube, all accessories available here that I’ll need for casting since this will be the start of this for me.

                            That means we still need 4 more orders to get this going. I’ll link back to the flex section and big bore area as well.

                            Sorry for the confusion, I should have been more clear and thanks Bob for mentioning it.

                            2016-02-21 at 06:40 #502521
                            adamsutherland
                            Moderator
                              Up
                              0
                              Down
                              ::

                              Updated.

                              2016-02-23 at 14:55 #502522
                              travismunden
                              Participant
                                Up
                                0
                                Down
                                ::

                                Hi, please put me in for the aluminum RG2 w/mold wrenches and spruce lube.

                                2016-02-24 at 07:51 #502523
                                adamsutherland
                                Moderator
                                  Up
                                  0
                                  Down
                                  ::

                                  List updated.

                                  2016-02-26 at 17:27 #502524
                                  tomkerrigan
                                  Participant
                                    Up
                                    0
                                    Down
                                    ::

                                    Ok, you got me, I’ll take a two cavity aluminum.  Regards, Tom

                                  • Author
                                    Replies
                                  Viewing 15 replies - 16 through 30 (of 72 total)
                                  1 2 3 4 5
                                  • You must be logged in to reply to this topic.