300 Blk Bullet for dummies (easy to cast, powder coat, and load bullet for subs)

This topic is empty.

Creator

Topic
2018-03-07 at 18:48 #489591
Full.Lead.Taco
Keymaster
Up
0
Down
::
I’ve been thinking about drawing up a heavy bullet for 300 blk shooters which would be designed in such a way that feeding is not affected by how thick the powdercoating goes on. So, hitek, spray PC, or shake and bake PC would all be easy to use and not affect feeding and chambering of the bullet in an AR15. Anybody interested in such a bullet?
Creator

Topic

Viewing 15 replies - 1 through 15 (of 43 total)

1 2 3 →

Author

Replies
2018-03-12 at 04:57 #510204
jamesbonvell
Up
0
Down
::
Id be interested. What do you have in mind
2018-03-12 at 20:25 #510205
joshuabrandon
Participant
Up
0
Down
::
I would be very interested in this. Would prefer plain base, brass, 4 Cavity mold. Would be willing to swing for something similar in hollow point. If that already exists then I will eventually find it. I am new to casting (but not too reloading) and some of the terminology and abbreviations are still confusing.
2018-03-13 at 13:44 #510206
Full.Lead.Taco
Keymaster
Up
0
Down
::
I will try to draw it up and then we can modify it as needed.
2018-03-14 at 14:46 #510207
Full.Lead.Taco
Keymaster
Up
0
Down
::
Something like this is what I have in mind. Made to be able to feed right in AR15’s as well as no finicky bore ride section on the nose for chambering easier when powder coated. Open to ideas for modifications. Would sit deep in the 300 blk case–but should still be fine for subsonic shooting. I kind of want it for simple easy casting, powder coating, and loading for subsonic 300 blk shooting/plinking.
2018-03-14 at 23:10 #510208
Greg Parsons
Participant
Up
0
Down
::
Would a gas check help at all you think?

Greg
2018-03-14 at 23:44 #510209
Full.Lead.Taco
Keymaster
Up
0
Down
::
We could do both… Gas check or plain base options.
2018-03-15 at 14:33 #510210
Full.Lead.Taco
Keymaster
Up
0
Down
::
Have you seen our abbreviation post with all the explanations?

http://noebulletmolds.com/smf/index.php/topic,2338.0.html

I would be very interested in this. Would prefer plain base, brass, 4 Cavity mold. Would be willing to swing for something similar in hollow point. If that already exists then I will eventually find it. I am new to casting (but not too reloading) and some of the terminology and abbreviations are still confusing.
2018-03-21 at 19:22 #510211
joshuabrandon
Participant
Up
0
Down
::
I did finally find it thanks It for sure made things easier!
2018-03-23 at 12:35 #510212
tanguydepenfentenyo
Up
0
Down
::
I’d be interested.
Is it possible with this design to have a HP ?
2018-03-23 at 13:09 #510213
Full.Lead.Taco
Keymaster
Up
0
Down
::
That might be possible.

I’d be interested.
Is it possible with this design to have a HP ?
2018-03-26 at 08:11 #510214
tanguydepenfentenyo
Up
0
Down
::
Maybe a little heavier too? To help cycling in semi-autos?
2018-03-26 at 18:26 #510215
Full.Lead.Taco
Keymaster
Up
0
Down
::
it should cycle just fine with either cfeblk, a1680, etc…
2018-04-26 at 19:03 #510216
joshuabrandon
Participant
Up
0
Down
::
Any new movement on this? I am still very interested.
2018-04-26 at 19:08 #510217
Full.Lead.Taco
Keymaster
Up
0
Down
::
Any changes that you guys would like to see on the bullet besides a gas check option?
2018-04-26 at 23:29 #510218
bryanalder
Participant
Up
0
Down
::
HP version
Author

Replies

Viewing 15 replies - 1 through 15 (of 43 total)

1 2 3 →

You must be logged in to reply to this topic.