.32 ACP and .380 ACP Ranch Dog Relaunch?

This topic is empty.

Creator

Topic
2015-08-18 at 04:19 #488227
erikdorothy
Participant
Up
0
Down
::
Needing molds for my various pocket autos, and would prefer to tumble lube for this application. . .therefore Ranch Dogs seem like just the ticket. http://www.ranchdogoutdoors.com has the prints for both the 75 grain flat nosed .314 and the 100 grain flat nosed .358.

I’d be a player for a 4 cavity solid for each. Anyone else?
Creator

Topic

Viewing 15 replies - 31 through 45 (of 48 total)

← 1 2 3 4 →

Author

Replies
2015-11-27 at 01:19 #499780
erikdorothy
Participant
Up
0
Down
::
Damned if I know Hamish. What with the proliferation of polymer framed nasal inhalers these last five years or so, I’d have thought the .380 would have been a rapidly turning slam dunk. It’s even a .358, and so is usable in ALL MANNER of things. As such, I’m a bit surprised to see it trailing behind the .32 in level of interest.
2015-11-27 at 11:26 #499781
teemu
Participant
Up
0
Down
::
If I count right it is 8 interested that .32… So two more and we are moving ahead..
2015-12-01 at 04:23 #499782
mikehupp
Participant
Up
0
Down
::
Shameless bump. I have plenty of projects and plenty of plated 380 bullets but I like this bullet.
2015-12-02 at 02:02 #499783
erikdorothy
Participant
Up
0
Down
::
Maybe if we all send Swede a video clip of each of us lying face down on the floor, kicking our hands and feet, and going “WAAAAAAAAAH!”

Think it’ll work?
2015-12-23 at 20:20 #499784
Cord
Participant
Up
0
Down
::
One way to take that .32 over the top is for two casters to step up and buy TWO each!

Might sound crazy, but it’s guaranteed to work….

The .358-100 is still too far away for that, but if it gets closer I will think about it.
2015-12-23 at 21:02 #499785
teemu
Participant
Up
0
Down
::
I did it already with two other molds so I have no capital make it again…
2015-12-24 at 01:10 #499786
amranch
Up
0
Down
::
Sorry you 32 guys. I would like to put my hat in the ring for the 380. My wife is receiving an LCR 38 for Christmas and this should make it a little easier to tame. RG 4 pb alum.
2015-12-24 at 04:11 #499787
erikdorothy
Participant
Up
0
Down
::
.32 – holding at 8

.380 – up to 6
2015-12-31 at 03:22 #499788
Treekiller
Up
0
Down
::
Could not find what number of cavities and designs this 32 mold will be cut in. I want to order one.
Dan
2015-12-31 at 03:31 #499789
erikdorothy
Participant
Up
0
Down
::
Treekiller, we’ll probably get our choices spelled out in greater detail when this buy goes active, but check out the Active Group Buys section to get an idea. You’ll probably have the option of at least 2, 4, and 5 cavities for solids, and 2 and 4 for hollow points. Aluminum for a certainty, brass as a possibility.

NINE players for the .32 (allllllllmost there!)

.380 holding at SIX
2016-01-01 at 04:26 #499790
Treekiller
Up
0
Down
::
Thanks for the PM and reply here.
I want a 32cal mold.
Dan
2016-01-07 at 00:18 #499791
johanstlund
Up
0
Down
::
Well it’s close to christmas, lets GO!

I want 32 75gr 2 cav aluminium

From Sweden
2016-01-07 at 05:43 #499792
erikdorothy
Participant
Up
0
Down
::
TEN! TEN for the .32! Let’s ROLL! Right at the same time my .416 Rigby mold buy finishes up. Christmas came late, but damned if it isnt here!

I’ve asked elsewhere, but not yet had much reply – does anyone have informed opinions on brass (getting enough heat in) vs. aluminum (keeping enough heat in) on smaller cavity molds like this?
2016-01-08 at 09:12 #499793
teemu
Participant
Up
0
Down
::
2016-01-09 at 21:47 #499794
Springerman54
Up
0
Down
::
Please put me down for an Aluminum 2 cavity .32 ACP 75 gr. Ranch Dog Mold. Just let me know how I need to proceed on payment, etc. Thanks !
Author

Replies

Viewing 15 replies - 31 through 45 (of 48 total)

← 1 2 3 4 →

You must be logged in to reply to this topic.