9mm 147 Grain Bevel Base

Up

0

Down

::

Any interest in a 147 grain bevel base mold for 9mm?  Bevel base would be for deep seating in the tapered case.  I prefer 147 grains as a solid.  I have a bunch of 9s that prefer the heavyweights.  Already have molds to cover the other weights.  Need a 147 grain to round out the collection 

Topic

[andyadkinsParticipant]

Up

0

Down

::

guys I am such a putz :o. 9X18 is a typo. You guys all know what I meant .

[charlesnuss]

Up

0

Down

::

It appears that the NOE signup design has a step from .358 down to .352 right at the driving band, and then another step down to .346 midway to the shoulder of the cone.

I liked the original idea of a 2 degree taper starting at the front of the first driving band and ending at .346. This had no step immediately in front of the first driving band. Reply #37 was the design, which I think is also shown in Reply #72.

Is this correct?

[randypatterson]

Up

0

Down

::

It appears that the NOE signup design has a step from .358 down to .352 right at the driving band, and then another step down to .346 midway to the shoulder of the cone.

I liked the original idea of a 2 degree taper starting at the front of the first driving band and ending at .346. This had no step immediately in front of the first driving band. Reply #37 was the design, which I think is also shown in Reply #72.

Is this correct?

That .352 measurement that you see is halfway between the .358 driving band and the .342 edge of the cone. I think it just designates the amount of taper and the middle of the taper measurement. The picture on the left side of the drawing shows a taper and not a step. It has to do with the limitations of the drawing software to represent a small angle. It uses a stepped horizontal line instead of a proper angled line. If you look closely at the front taper, it is represented by a series of small horizontal lines.

[daveridenourParticipant]

Up

0

Down

::

Charlie,

I believe Tazman is correct. That’s the way I read the drawing too.

Dave

[charlesnuss]

Up

0

Down

::

Just wanting to make sure. There is a difference in the drawings at the point of the front driving band forward.

[sgt.mike]

Up

0

Down

::

Dog gone it AL and crew,
I only have soo much disposable income LMAO  great looking bullet…

[randypatterson]

Up

0

Down

::

I want to thank Frank and others for all the good drawings and ideas that have been put forward. It’s nice to see people working together to get a good idea going.

[frankelliottParticipant]

Up

0

Down

::

You guys are all very welcome, I’m happy to do it.

Frank

[SwedeNelsonKeymaster]

Up

0

Down

::

Rattlesnake Charlie

What are the differences and I will check it out
I cant see them (post #72 and the Group Buy drawing?)

Bullet maker, maker
Al Nelson

[stephandegroat]

Up

0

Down

::

Cost? Hp? How many cavities?

[SwedeNelsonKeymaster]

Up

0

Down

::

stevo629

You can see it here:
http://noebulletmolds.com/smf/index.php/topic,644.0.html

Bullet maker, maker
Al Nelson

[charlesnuss]

Up

0

Down

::

Rattlesnake Charlie

What are the differences and I will check it out
I cant see them (post #72 and the Group Buy drawing?)

Bullet maker, maker
Al Nelson

See Reply #77.
Others have assured me that we still have the taper from front driving band, and not a step, so I’m OK with the design.

[charlesnuss]

Up

0

Down

::

I want
RG4 cavity $133.00
RG4 blank pin set $9.00

[Author]

Replies