TL452-230-RF (BB) 45ACP, 45AR

Up

0

Down

::

NOE TL4524-230-RF (BB) 
We will be running this like a inventory run

http://noebulletmolds.com/photos/albums/TL452-230-RF-BB-/TL452-234-RF_-BB-_234_gr_Sketch.Jpg%5B/img%5D

http://noebulletmolds.com/photos/albums/TL452-230-RF-BB-/N.O.E._Bullet_Moulds_TL452-234-RF_-BB-_234_gr_Sketch.Jpg%5B/img%5D

http://noebulletmolds.com/photos/albums/TL452-230-RF-BB-/N.O.E._Bullet_Moulds_TL452-220-HP_-BB-_220_gr_Sketch.Jpg%5B/img%5D

We will be running 2 cavity, 2 cavity Brass, 3 cavity, 4 cavity, 4 cavity Brass, 5 cavity, RG2 and RG4
Aluminum and Brass. Bevel base only.

We offer Blank RG pins on our website for you that like to make your own.
Top punch, wrenches and sprue lube are extras now if you want them

Prices will be our standard website prices ( http://www.noebulletmoulds.com )
2 cavity $79.00
2 cavity Brass $101.00
4 cavity $92.00
4 cavity Brass $114.00
5 cavity $99.00
RG2 cavity $103.00
RG2 cavity Brass $125.00
RG4 cavity $133.00
RG4 cavity Brass $155.00

Lyman/RCBS style Top Punch $5.00
Saeco style Top Punch $7.50
Mould Wrenches / Sprue Lube $2.50
RG2 blank pin set $4.50
RG4 blank pin set $9.00

Will run this as soon as we get 10 signed up and we get the tooling in.
Will have them listed on our website as a inventory item as soon as we have them ran
So you can use Pay-Pal, Credit Card or Check / Money order
Post a “I want” and receive a 15% discount off the website
We will PM a discount code for you to use at check out

If you have question – Visit our website or PM me

Thanks
Swede Nelson

Topic

[markusmaaskeParticipant]

Up

0

Down

::

Order is placed…can’t wait to cast with this mold.

Thanks AL

[gregsutherlandParticipant]

Up

0

Down

::

Hi Al,
Got the mould ordered, however, the provision for getting it drilled, and ordering the top punch weren’t available to choose or get them paid for..  Would like those two items with the mould as well!! and, can get the balance caught up sooner than later!!
Looking forward to working with this bullet! Will use it in both the .45 ACP as well as the .45 Colt!
Greg S.

[erikdorothyParticipant]

Up

0

Down

::

Placed the order for my two last night.  Seeing that the RG mold comes with THREE pin sets was a pleasant surprise.  I’m thinking that cup point is going to come in real handy for the .45 Colt – I’ve been hoping for something that performs between the two extremes of police duty loads for the penetrationally-paranoid and deep drilling solids.

REALLY looking forward to these.  Thanks for the run Al, and thanks to Ranch Dog for feeding the vision!

[gregsutherlandParticipant]

Up

0

Down

::

Howdy,,,
As usual Mr. Al came through way above expectations covering me on the “other stuff” of the mould order,, Thank You Sir!!

But, the Good news for me is,, I can cast these bullets, tumble lube them, and Load them,, !!!
The mould throws bullets so consistently that No Sizing is necessary for the gals I go with!!  In either .45 Colt in revolvers or .45 ACP loadings for pistols and revolvers!!
I’ve run about a 1000 of these with nothing but success!!!

What a wonderful, quality piece of equipment/tackle!!
Thank You again !!

[erikdorothyParticipant]

Up

0

Down

::

Stray,

Thanks for the update.  I have yet to get past heat-cycling mine in the stove.  They arrived about 2 days before my deer season started, so my energies have been diverted elsewhere, but it sounds like you’re taking it down both the Colt and ACP roads I intend for myself.  Thus far, I’ve been shooting my Dad’s 270 grain Casull bullets in my 4.2″ Redhawk with good results, but it’s killin’ a little more on the back end than I’d like.  I think this is the magic it’s looking for.

[Author]

Replies