250-51-FN (Bob’s Boat Tail) -14- GB260 2/22/16

This topic is empty.

Creator

Topic
2015-11-22 at 20:26 #488449
SwedeNelson
Keymaster
Up
0
Down
::
NOE 250-51-FN (Bob’s Boat Tail)
We will be running this like a inventory run

LAST CALL
This will be on the Mill next

http://noebulletmolds.com/photos/albums/250-51-FN-BT-/250-51-FN_-BT-__51_gr_Sketch.Jpg%5B/img%5D

http://noebulletmolds.com/photos/albums/250-51-FN-BT-/N.O.E._Bullet_Moulds_250-51-FN_-BT-__51_gr_Sketch.Jpg%5B/img%5D

http://noebulletmolds.com/photos/albums/250-51-FN-BT-/N.O.E._Bullet_Moulds_250-48-HP_-BT-___48_gr_Sketch.Jpg%5B/img%5D

Will offer this one .252/.250 and .255/.253 diameter.

We will be running 2 cavity, 2 cavity Brass, 3 cavity, 4 cavity, 4 cavity Brass, 5 cavity Bevel Base only.
We will offer a Lyman type single pin Hollow Point system in one cavity of any of the above moulds.
Top punch, wrenches and sprue lube are extras now if you want them

All moulds will be assumed to be Aluminum unless Brass is requested!

Prices will be our standard website prices ( http://www.noebulletmoulds.com )
2 cavity $79.00
2 cavity Brass $101.00
3 cavity $86.00
4 cavity $92.00
4 cavity Brass $114.00
5 cavity $99.00

Lyman type single pin Hollow Point $35.00
Lyman/RCBS style Top Punch $5.00
Saeco style Top Punch $7.50
Mould Wrenches / Sprue Lube $2.50
RG2 blank pin set $4.50
RG4 blank pin set $9.00

Will run this as soon as we get 10 signed up and we get the tooling in.
Will have them listed on our website as a inventory item as soon as we have them ran
So you can use Pay-Pal, Credit Card or Check / Money order
Post a “I want” and receive a 15% discount off the website
We will PM a discount code for you to use at check out

If you have question – Visit our website or PM me

Thanks
Swede Nelson
Creator

Topic

Viewing 15 replies - 16 through 30 (of 89 total)

← 1 2 3 4 5 6 →

Author

Replies
2015-12-11 at 12:37 #501577
denisbeaudry
Participant
Up
0
Down
::
A two cavity aluminium with hp pin on one side for me in 255/.253 .will I need the wrench and lube. This is for a complete newby ,I don’t have a pot yet .
2015-12-11 at 13:32 #501578
adamsutherland
Moderator
Up
0
Down
::
List updated.
2015-12-14 at 20:08 #501579
denisbeaudry
Participant
Up
0
Down
::
My bad, I modified my original post instead of posting new. I’d need the mould in .255/253 not the 252/250.
2015-12-15 at 05:06 #501580
adamsutherland
Moderator
Up
0
Down
::
Updated.
2015-12-23 at 02:16 #501581
maxgarnett
Up
0
Down
::
I have never used the shop for a buy in on the group buy can I call in the order and just spec that it is air gun buy in .25 cal 252/250 etc . Code for buy ?? I am kinda not PC smart.
thanks
2015-12-23 at 02:28 #501582
maxgarnett
Up
0
Down
::
Sorry a double , I tend to use army short hand DBL, is two cavity. I also plan on a 30 cal for a Flex now, and a 35 for future use.
thanks
2015-12-23 at 08:59 #501583
adamsutherland
Moderator
Up
0
Down
::
You need to sign up here to get the discount code.

The GB will be run when there are 10 signed up members, Al will send out the codes when the buy.is closed and he is going to put the design on the mill.

It is all explained on stickies on these forums, have a look.
2015-12-23 at 14:09 #501584
maxgarnett
Up
0
Down
::
HI
Thanks for help.
But what is a stikie,!!!!. I went to his sight and could not find a place to order or pay for this item, When I said I was a PC idjet I was not joking. Also the size of die. It is for an airforce escape in .25 cal anyone know the proper drive band dia for air force barrels.
thanks
2015-12-23 at 14:25 #501585
adamsutherland
Moderator
Up
0
Down
::
Reread my previous post, there will be nothing on the web shop ’till this group buy thread is complete and there are ten signed up.

Then you will get the discount code here via PM and can order and pay on the web shop when the moulds will be there for sale,

A sicky is a thread that is stuck to the top of a forum so that they are not lost.
2015-12-23 at 14:43 #501586
maxgarnett
Up
0
Down
::
OK
I will try this again. please bear with me . I want a 51 grain 2 cavity mold 250/252 OAL of no more then .450 for a 25 cal. pcp airforce/benji.
Anything else?
I did reread your post and it made the same sense to me as the first time , which is back to my comment I don’t under stand this PC stuff. I can read a map , use a compass , build a road , bridge etc but I really do not get this web site stuff.
thanks
2015-12-23 at 15:23 #501587
maxgarnett
Up
0
Down
::
OK
I called air force and there 25 cal. escape has a land dia. of .249 and a groove dia. of .255, ? what should the driving band dia be on the boat tail buy. This is for the order above ? anyone have a answer please.
thanks
2015-12-23 at 16:04 #501588
adamsutherland
Moderator
Up
0
Down
::
I want a 51 grain 2 cavity mold 250/252 OAL of no more then .450 for a 25 cal. pcp airforce/benji.
Anything else?

Brass or aluminium mould?
2015-12-23 at 16:15 #501589
maxgarnett
Up
0
Down
::
Alum please
thank you
2015-12-23 at 16:49 #501590
adamsutherland
Moderator
Up
0
Down
::
List updated.
2015-12-23 at 19:58 #501591
rsterne
Participant
Up
0
Down
::
cpt_sfc…. For a barrel that is 0.249″ land and 0.255″ groove, I would suggest you purchase the larger size…. 0.255/0.253….

Bob
Author

Replies

Viewing 15 replies - 16 through 30 (of 89 total)

← 1 2 3 4 5 6 →

You must be logged in to reply to this topic.