250-51-FN (Bob’s Boat Tail) -14- GB260 2/22/16

Home › Forums › NOE Forums › NOE Archive › Historical Archive › Group Buys › Archived Buys › 250-51-FN (Bob’s Boat Tail) -14- GB260 2/22/16

  • This topic is empty.
Viewing 15 replies - 46 through 60 (of 89 total)
  • Author
    Replies
  • #501607
    teemu
    Participant
      Up
      0
      Down
      ::

      I want 3 cav. .255/.253 alu with single Lyman style HP pin  Thanks

      If 3-cav is possible..there is no price for 3-cav mold on this group buy,but that .250 41-FN is listed 3-cav. price.

      If 3-cav is not available I take 4-cav. alu with same HP option

      #501608
      adamsutherland
      Moderator
        Up
        0
        Down
        ::

        List updated.

        Al notified.

        #501609
        rsterne
        Participant
          Up
          0
          Down
          ::

          I measured my Hatsan .25 cal barrel on the AT-44 Long this morning, as best I could without removing it from the gun…. Here is what I found….

          Muzzle – pushed a .257 cal bullet in 1/2″ and pulled it back out…. 0.249″ land (or smaller)…. 0.255″ groove….
          Breech – I chambered a .250 cal BBT by closing the bolt, and then pushed it back out…. no marks at all…. none…. and no resistance to chambering….
          Twist – 17.5″

          With these measurements being nearly identical to those for a LW barrel, and Hatsan supplying both…. I suspect they copied LW’s stated dimensions of 0.248″ land and 0.254″ groove with a 17.7″ twist…. Those measurements would be within my measurement tolerances….

          If you are ordering either the 41 gr. or 51 gr. BBT from NOE for a Hatsan, I would suggest the 41 gr. in the larger size (0.255″/0.253″)…. If you want to try the 51 gr., you should be aware that since it has a recommended twist of 16″, if you push it too close to Mach 1, you may have a stability problem in the Hatsan barrels…. However, the Stability Factor works out to the recommended SF = 1.5 at 800 fps for the 51 gr in a 17.5″ twist…. so you will likely be fine at any velocity you could likely reach in a Hatsan, even a fully modded BT-65….

          Bob

          #501610
          rsterne
          Participant
            Up
            0
            Down
            ::

            dromia, please note my order should show that I want the HP pin version….

            Bob

            #501611
            adamsutherland
            Moderator
              Up
              0
              Down
              ::

              If you want to change an order then editing the original won’t do it, you need to post in the thread as an addition.

              Life is too short to re-read every thread, I just go on from my last post.

              #501612
              adamsutherland
              Moderator
                Up
                0
                Down
                ::

                Updated.

                If people want to change an order then editing the original won’t do it, you need to post in the thread as an addition.

                Life is too short for me to re-read every thread, I just go on from my last post.

                #501613
                tomkerrigan
                Participant
                  Up
                  0
                  Down
                  ::

                  Put me down for a 250-51-fn 4 cavity $92.00.  Regards, Tom

                  #501614
                  adamsutherland
                  Moderator
                    Up
                    0
                    Down
                    ::

                    List updated.

                    #501615
                    SwedeNelson
                    Keymaster
                      Up
                      0
                      Down
                      ::

                      All NEW Group Buys are “ON HOLD”.
                      Our tool grinder is down and we cant get new form tools.
                      We are looking at other makers and avenues to work this out.
                      This is only a delay and we will get it resolved as soon as we can.

                      Sorry for the inconvenience
                      Bullet maker, maker
                      Al Nelson

                      #501616
                      johnpedro
                        Up
                        0
                        Down
                        ::

                        Thank you for the notification.

                        #501617
                        denisbeaudry
                        Participant
                          Up
                          0
                          Down
                          ::

                          Please add a single hp pin to my mold .thanks

                          #501618
                          thomasraether
                            Up
                            0
                            Down
                            ::

                            If it is possible to still get in on this, I want a .255″ 2 cavity for an AirForce barrel. Thank you!

                            #501619
                            adamsutherland
                            Moderator
                              Up
                              0
                              Down
                              ::

                              List updated.

                              #501620
                              thomasraether
                                Up
                                0
                                Down
                                ::

                                Ok, my wife told me to upgrade my initial request, and who am I to argue with that? So now I want, still in .255″ for an AirForce barrel, an aluminum 5 cavity with hollow point.  Thank you!!

                                #501621
                                adamsutherland
                                Moderator
                                  Up
                                  0
                                  Down
                                  ::

                                  List updated.

                                Viewing 15 replies - 46 through 60 (of 89 total)
                                • You must be logged in to reply to this topic.